私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
WEP012832Aは128x32 ピクセルの 2.23インチCOG+PCB 有機ELモジュールです。SSD1305 ICを内臓し、、6800/8080 8ビットパラレル、I2C、4線シリアルのインターフェースをサポート致します。電源電圧は3V~5Vです。
WEP012832AはCOG 構造で、PCB基板とフレームを搭載しております。20 ピンと8ピンは基板固定用ピンです。また、ネジ止め固定することも選択できます。PIN+FPC(コネクタ必要)、或いはHot barなども対応可能で す。但し、型番は違います。必要がある場合、当社の営業担当者に御連絡ください。 また、振動モーターとブザーも追加しております。
WEP012832AはAI家電製品、医療機器、Smart Control、メーター などに適しております。操作温度範囲は–40℃ to +80℃で、保存温度範囲は –40℃ to +85℃です。
項目 | 仕様 | 単位 |
---|---|---|
解像度 | 128 × 32 | Dots |
外形寸法 | 66.5 × 35.0 × 9.0(Max) | mm |
有効エリア | 55.018 × 13.098 | mm |
ドットサイズ | 0.408 × 0.388 | mm |
ドットピッチ | 0.43 × 0.41 | mm |
表示モード | パッシブマトリクス | |
発光色 | モノクロ | |
駆動方法 | 1/32 Duty | |
IC | SSD1305 | |
Buzzer | OBO-11241SB | |
Vibration Motor | W0625AB001F | |
インターフェイス | 6800, 8080, SPI, I2C | |
サイズ | 2.23 インチ |
項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
ロジック電源電圧 | VDD | - | 3.0 | 3.3 | 3.5 | V |
高レベル入力 | VIH | - | 0.8×VDD | - | VDD | V |
低レベル入力 | VIL | - | 0 | - | 0.2×VDD | V |
高レベル出力 | VOH | IOUT = 100uA, 3.3MHz | 0.9×VDD | - | VDD | V |
低レベル出力 | VOL | IOUT = 100uA, 3.3MHz | 0 | - | 0.1×VDD | V |
Supply Voltage for Buzzer | BSW | 50% square | 0.8×VDD | - | VDD | V |
Supply Voltage for Vibration Motor | MSW | - | 2.7 | - | 3.3 | V |
Operating Current at Display with 50% Check Board | IDD | VDD=3.3V | - | 90 | 120 | mA |
パラメーター | 記号 | 最小値 | 最大値 | 単位 |
---|---|---|---|---|
ロジック電源電圧 | VDD | -0.3 | 4.0 | V |
操作温度 | TOP | -40 | +80 | °C |
保存温度 | TSTG | -40 | +85 | °C |
No. | 記号 | 説明 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground. | |||||||||||||||
2 | VDD | Power supply pin for core logic operation. | |||||||||||||||
3 | V0 | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
4 | D/C# | This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDDIO), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
5 | R/W# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDDIO) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
6 | E/RD# | When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDDIO) and the chip is selected. When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
7~14 | DB0~DB7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be left opened. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
15 | CS# | This pin is the chip select input. (active LOW) | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDDIO) during normal operation. |
|||||||||||||||
17,18 | BS2,BS1 | Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
19 | N.C. | No connection. | |||||||||||||||
20 | FG(GND) | Ground. | |||||||||||||||
21~25 | N.C. | No connection. | |||||||||||||||
26 | VSS | Ground. | |||||||||||||||
27 | BSW | Control the Piezoelectric Buzzer. | |||||||||||||||
28 | MSW | Control the BLDC Vibration Motor. |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー