Módulo de pantalla gráfica OLED 0,68 pulgadas 96x32 - WEO009632C

Módulo de pantalla gráfica OLED 0,68 pulgadas 96x32

Modelo Nº WEO009632C

►Tipo: Gráfico
►Estructura: COG
►Tamaño : 0,68 pulgada
►Matriz de puntos 96 x 32
►IC：SSD1315
►Fuente de alimentación de 3V
►1/32 duty
►Interfaz : 6800, 8080, SPI, I2C
►Color de la pantalla: Blanco / Amarillo
►Otras opciones de FPC disponibles en la siguiente tabla.

DESCARGAR PDF

CÓDIGO DEMO AÑADIR A PREGUNTA

PREV. VOLVER A LA LISTA SIGUIENTE

Descripción

El WEO009632C es una mini pantalla OLED con una resolución de 96×32 píxeles y un tamaño diagonal de 0,68 pulgadas. Integra el controlador SSD1315 y es compatible con interfaces paralelas de 8 bits 6800/8080, I²C y SPI de 4 hilos. El voltaje de alimentación lógica es de 3V, con un ciclo de trabajo de 1/32, y la corriente típica de la pantalla bajo un patrón de tablero de ajedrez al 50% es de 3,6mA @ 12Vcc. Este módulo OLED funciona en temperaturas de -40℃ a +80℃ y puede almacenarse entre -40℃ y +85℃. Winstar ofrece versiones ZIF FPC y Hotbar, lo que permite a los clientes elegir la opción más adecuada para sus aplicaciones.

El mini módulo COG PMOLED WEO009632C es ultra delgado con solo 1,21 mm, ligero y de bajo consumo de energía. Es ideal para dispositivos portátiles, aplicaciones de hogar inteligente, instrumentos portátiles, medidores, equipos de cuidado personal, bolígrafos grabadores de voz, dispositivos de salud y mucho más.

Opciones de FPC

96x32 Gráficos OLED, 0.68 pulgada OLED, WEO009632C

DIBUJO

WEO009632C with ZIF FPC

0.68 inch 96x32 Graphic OLED Display with ZIF FPC - WEO009632C

Data source ref: WEO009632CLAP3N00000

WEO009632C with Hotbar FPC

0.68 inch COG Graphic Display with Hotbar FPC - WEO009632C

Data source ref: WEO009632CWPP3N00H00

ESPECIFICACIONES

Datos mecánicos

Elemento	Dimensión	Unidad
Resolución	96 × 32	puntos
Dimensión del módulo	19.80 × 12.32 × 1.21	mm
zona activa	16.298 × 5.418	mm
Tamaño del punto	0.148 × 0.148	mm
Distancia entre puntos	0.17 × 0.17	mm
Modo de visualización	Matriz pasiva
Color de la pantalla	Monocromos
Drive Duty	1/32 Duty
IC	SSD1315
Interfaz	6800, 8080,4-Wire SPI, I2C
Diagonal	0.68 pulgada

Valores nominales máximos absolutos

Parameter	Símbolo	Valor mín.	Valor típico	Valor máx.	Unidad
Supply Voltage for Logic	VDD	-0.3	-	4	V
Supply Voltage for Display	VCC	0	-	18	V
Temperatura de funcionamiento	TOP	-40	-	+80	°C
Temperatura de almacenamiento	TSTG	-40	-	+85	°C

Características electrónicas

DC electrónicas

Elemento	Símbolo	Condición	Valor mín.	Valor típico	Valor máx.	Unidad
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Supply Voltage for Display	VCC	－	7.5	12.0	12.5	V
High Level Input	VIH	－	0.8×VDD	－	VDD	V
Low Level Input	VIL	－	0	－	0.2×VDD	V
High Level Output	VOH	Iout = 100uA	0.9×VDD	－	VDD	V
Low Level Output	VOL	Iout = 100uA	0	－	0.1×VDD	V
Display 50% Pixel on	ICC	VCC=12V	－	5.0	7.5	mA

Función interfaz Pin

No.

Símbolo

Función

VSS

Ground pin. It must be connected to external ground.

No connection

VDD

Power supply pin for core logic operation.

4~8

No connection

VDD

Power supply pin for core logic operation.

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select

BS[2:1]	Interface
00	4 line SPI
01	I2C
11	8-bit 8080 parallel
10	8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

BS2

No connection

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.

D/C#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.

W/R#

This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

IREF

This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.