N° de modèle WEO009632C
►Type: Graphique
►Structure: COG
►Dimension: 0.68 pouces
►Matrice de points 96 x 32
►IC：SSD1315
►Alimentation 3V
►1/32 duty
►Interface: 6800, 8080, SPI, I2C
►Couleur d'affichage: Blanc / Jaune
►Autres options FPC disponibles dans le tableau ci-dessous
Le WEO009632C est un mini écran OLED avec une résolution de 96×32 pixels et une taille diagonale de 0,68 pouce. Il intègre le contrôleur SSD1315 et prend en charge les interfaces parallèles 8 bits 6800/8080, I²C et SPI à 4 fils. La tension d’alimentation logique est de 3V, avec un cycle de service de 1/32, et le courant typique de l’affichage sous un motif en damier à 50 % est de 3,6mA @ 12Vcc. Ce module OLED fonctionne à des températures comprises entre -40℃ et +80℃ et peut être stocké entre -40℃ et +85℃. Winstar propose des versions ZIF FPC et Hotbar, permettant aux clients de choisir l’option la plus adaptée à leurs applications.
Le module mini COG PMOLED WEO009632C est ultra-fin avec seulement 1,21 mm, léger et à faible consommation d’énergie. Il est idéal pour les dispositifs portables, les applications de maison intelligente, les instruments portatifs, les compteurs, les appareils de soins personnels, les stylos enregistreurs vocaux, les dispositifs de santé et bien plus encore.
s domotiques intelligentes, aux appareils portables, aux appareils de mesure, aux appareils de soins personnels, aux stylos enregistreurs vocaux, aux appareils de santé, etc.
| Article | Dimensions | Unité |
|---|---|---|
| Résolution | 96 × 32 | points |
| Dimensions du module | 19.80 × 12.32 × 1.21 | mm |
| Zone active | 16.298 × 5.418 | mm |
| Taille des points | 0.148 × 0.148 | mm |
| Pas des points | 0.17 × 0.17 | mm |
| Mode d'affichage | Matrice passive | |
| Couleur d'affichage | Monochrome | |
| Drive Duty | 1/32 Duty | |
| IC | SSD1315 | |
| Interface | 6800, 8080,4-Wire SPI, I2C | |
| Diagonale | 0.68 pouces | |
| Parameter | Symbole | Valeur min | Typ. | Valeur max | Unité |
|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | - | 4 | V |
| Supply Voltage for Display | VCC | 0 | - | 18 | V |
| Température de fonctionnement | TOP | -40 | - | +80 | °C |
| Température de stockage | TSTG | -40 | - | +85 | °C |
| Article | Symbole | État | Valeur min | Valeur type | Valeur max | Unité |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VCC | － | 7.5 | 12.0 | 12.5 | V |
| High Level Input | VIH | － | 0.8×VDD | － | VDD | V |
| Low Level Input | VIL | － | 0 | － | 0.2×VDD | V |
| High Level Output | VOH | Iout = 100uA | 0.9×VDD | － | VDD | V |
| Low Level Output | VOL | Iout = 100uA | 0 | － | 0.1×VDD | V |
| Display 50% Pixel on | ICC | VCC=12V | － | 5.0 | 7.5 | mA |
| No. | Symbole | Fonction | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
| 2 | NC | No connection | ||||||||||
| 3 | VDD | Power supply pin for core logic operation. | ||||||||||
| 4~8 | NC | No connection | ||||||||||
| 9 | VDD | Power supply pin for core logic operation. | ||||||||||
| 10 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||
| 11 | BS2 | |||||||||||
| 12 | NC | No connection | ||||||||||
| 13 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
| 14 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. | ||||||||||
| 15 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
||||||||||
| 16 | W/R# | This is read / write control input pin connecting to the MCU interface. When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
| 17 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
| 18 | D0 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||
| 19 | D1 | |||||||||||
| 20 | D2 | |||||||||||
| 21 | D3 | |||||||||||
| 22 | D4 | |||||||||||
| 23 | D5 | |||||||||||
| 24 | D6 | |||||||||||
| 25 | D7 | |||||||||||
| 26 | IREF | This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA. |
||||||||||
| 27 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||
| 28 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. |
| Image | FPC Length | PIN | pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
30 | 28 | 0.5 | ZIF FPC | 6800, 8080,4-Wire SPI, I2C | FPC2050002811XXXXX01 | 20180131 |
 |
8.479 | 25 | 0.65 | HOTBAR FPC | 6800, 8080,4-Wire SPI, I2C | FPC2065002501XXXXX00 | 20190906 |
En cliquant sur "Autoriser tous les cookies", vous acceptez le stockage de cookies sur votre appareil pour améliorer la navigation sur le site, analyser l'utilisation du site et aider dans nos efforts de marketing et de performance. Vous pouvez trouver plus d'informations à ce sujet dans notre politique. Politique de confidentialité
