Módulo de Display Gráfico OLED 0,68 polegadas 96x32 - WEO009632C

Módulo de Display Gráfico OLED 0,68 polegadas 96x32

Model No. WEO009632C

►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 0,68 polegadas
►Matriz de pontos 96x32
►IC：SSD1315
►Alimentação +3V
►1/32 duty
►Interface: 6800, 8080, SPI, I2C
►Display Color: Branco / Amarelo
►Other FPC options available in below table

PDF DOWNLOAD

DEMO CODE ADD TO INQUIRY

PREV. BACK to LIST NEXT

Descrição

O WEO009632C é um mini display OLED com resolução de 96×32 pixels e tamanho diagonal de 0,68 polegadas. Ele integra o controlador SSD1315 e suporta interfaces paralelas 8 bits 6800/8080, I²C e SPI de 4 fios. A tensão de alimentação lógica é de 3V, com ciclo de trabalho de 1/32, e a corrente típica do display sob um padrão em tabuleiro de xadrez de 50% é de 3,6mA @ 12Vcc. Este módulo OLED opera em temperaturas de -40℃ a +80℃ e pode ser armazenado entre -40℃ e +85℃. A Winstar oferece versões ZIF FPC e Hotbar, permitindo que os clientes escolham a opção mais adequada para suas aplicações.

O mini módulo COG PMOLED WEO009632C é ultra fino, com apenas 1,21 mm, leve e de baixo consumo de energia. É ideal para dispositivos vestíveis, aplicações de casa inteligente, instrumentos portáteis, medidores, aparelhos de cuidados pessoais, canetas gravadoras de voz, dispositivos de saúde e muito mais.

FPC Options

Display OLED 96x32 de 0,68 polegadas, WEO009632C

DRAWING

WEO009632C with ZIF FPC

0.68 inch 96x32 Graphic OLED Display with ZIF FPC - WEO009632C

Data source ref: WEO009632CLAP3N00000

WEO009632C with Hotbar FPC

0.68 inch COG Graphic Display with Hotbar FPC - WEO009632C

Data source ref: WEO009632CWPP3N00H00

SPECIFICATIONS

Dados Mecânicos

Item	Dimensão	Unidade
Matriz de pontos	96 × 32	ponto
Dimensão do módulo	19.80 × 12.32 × 1.21	mm
Área ativa	16.298 × 5.418	mm
Tamanho do ponto	0.148 × 0.148	mm
Distância entre pontos	0.17 × 0.17	mm
Modo de exibição	Passive Matrix
Cor de exibição	Monocromático
Drive Duty	1/32 Duty
IC	SSD1315
Interface	6800, 8080,4-Wire SPI, I2C
Tamanho	0,68 polegadas

Classificações Máximas Absolutas

Parameter	Símbolo	Valor Min	Valor Típico	Valor Máximo	Unidade
Supply Voltage for Logic	VDD	-0.3	-	4	V
Supply Voltage for Display	VCC	0	-	18	V
Temperatura de operação	TOP	-40	-	+80	°C
Temperatura de armazenamento	TSTG	-40	-	+85	°C

Características Eletrônicas

DC Características Eletrônicas

Item	Símbolo	Condição	Valor Min	Valor Típico	Valor Máximo	Unidade
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Supply Voltage for Display	VCC	－	7.5	12.0	12.5	V
High Level Input	VIH	－	0.8×VDD	－	VDD	V
Low Level Input	VIL	－	0	－	0.2×VDD	V
High Level Output	VOH	Iout = 100uA	0.9×VDD	－	VDD	V
Low Level Output	VOL	Iout = 100uA	0	－	0.1×VDD	V
Display 50% Pixel on	ICC	VCC=12V	－	5.0	7.5	mA

Função do pino de interface

No.

Símbolo

Função

VSS

Ground pin. It must be connected to external ground.

No connection

VDD

Power supply pin for core logic operation.

4~8

No connection

VDD

Power supply pin for core logic operation.

BS1

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 are pin select

BS[2:1]	Interface
00	4 line SPI
01	I2C
11	8-bit 8080 parallel
10	8-bit 6800 parallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

BS2

No connection

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

RES#

This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.

D/C#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.

W/R#

This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E/RD#

This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

IREF

This is segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for panel driving voltage. This is also the most positive power voltage supply pin.