首页 产品介绍 OLED显示屏 字符OLED显示屏 WEO002004C

2.89寸 20x4 COG SSD1311 OLED 显示模块

型号 WEO002004C

►类型:点阵字符型
►结构:COG
►20字x4行
►IC:SSD1311
►3V/5V电源电压
►1/32 duty
►接口:6800, 8080, SPI, I2C
►发光颜色: 白色 / 黄色
►其它FPC选项请参阅最下方表格说明

产品叙述

20x4 COG SSD1311 OLED 显示模块(型号:WEO002004C)采用 COG(Chip On Glass)设计,提供高性能且可靠的显示解决方案。这款 SSD1311 OLED 显示模块因其卓越的显示效果和出色的耐用性,适用于多种应用场合。

模块的外观尺寸为 84.5 x 27.5 mm,厚度为 2.17 mm,有效区域尺寸为 70.42 x 20.82 mm,对角线尺寸为 2.89 吋。内建 SSD1311 驱动 IC,WEO002004C 支持整合的字符集,包括 ASCII、英文、欧文和日文字符。每个字符由 5x8 像素组成,确保文字显示清晰细致。

此模块的显示模式为 4 行,每行可显示 20 个字符。由于 OLED 技术的自发光特性,该模块不需要背光,这使得设计更轻薄,对比度提升至 10,000:1。此外,模块拥有高达 175 度的超广视角,确保从不同角度观看时显示效果一致。模块还具有低功耗和广泛的工作温度范围,显示其多样性。

WEO002004C 的工作温度范围为 -40°C 至 +80°C,储存温度范围为 -40°C 至 +85°C,可在极端条件下稳定运行。模块的逻辑电压范围为 2.4V 至 3.3V,典型值为 3V,并使用 1/32 duty 驱动方式。

此外,WEO002004C 支持多种接口选择,包括 6800/8080 8-bit 并列接口和 I2C/SPI 串行接口,提供灵活的连接选择以满足不同系统需求。该模块系列还提供了各种软性印刷电路板(FPC)选择,以满足不同客户需求。

凭借其可靠的显示质量、广泛的工作温度范围和灵活的接口选择,WEO002004C OLED 显示模块搭配 SSD1311 驱动 IC 是传统 LCD 模块的实用替代品。我们建议考虑使用这款 20x4 字符 OLED 模块,以提升产品的显示性能,实现更高的显示质量和更低的能耗。

WEO002004C可选接口:6800 OLED显示模块,8080 OLED显示模块,SPI OLED显示模块,I2C OLED显示模块


     可选 FPC

 

规格图

SSD1331 OLED Display, 2.89 inches 20x4 COG OLED SSD1311 - WEO002004C

Data source ref: WEO002004CLPP5N00000

产品规格

Pin功能定义

Pin No. 符号 Pin 类型 说明
1 NC No connection
2 VSL P This is segment voltage (output low level) reference pin.
When external VSL is not used, this pin should be left open.
When external VSL is used, connect with resistor and diode to ground (details depend on application).
3 VSS P Ground pin. It must be connected to external ground.
4 REGVDD I Internal VDD regulator selection pin in 5V I/O application mode.
When this pin is pulled HIGH, internal VDD regulator is enabled (5V I/O application).
When this pin is pulled LOW, internal VDD regulator is disabled (Low voltage I/O application).
5 SHLC I This pin is used to determine the Common output scanning direction.
COM scan direction
SHLC COM scan direction
1 COM0 to COM31 (Normal)
0 COM31 to COM0 (Reverse)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
6 SHLS I This pin is used to change the mapping between the display data column address and the Segment driver.
SEG scan direction
SHLS SEG direction
1 SEG0 to SEG99 (Normal)
0 SEG99 to SEG0 (Reverse)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
7 VDD P Power supply for core logic operation.
VDD can be supplied externally or regulated internally.
In LV IO application (internal VDD is disabled), this is a power input pin.
In 5V IO application (internal VDD is enabled), VDD is regulated internally from VDDIO.
A capacitor should be connected between VDD and VSS under all circumstances.
8 VDDIO P Low voltage power supply and power supply for interface logic level in both Low Voltage I/O and 5V I/O application. It should match with the MCU interface voltage level and must be connected to external source.
9 BS0 I MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
Bus Interface selection
BS[2:0] Interface
000 Serial Interface
001 Invalid
010 I2C
011 Invalid
100 8-bit 6800 parallel
101 4-bit 6800 parallel
110 8-bit 8080 parallel
111 4-bit 8080 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
10 BS1
11 BS2
12 GPIO I/O It is a GPIO pin. Details refer to OLED command DCh.
13 CS# I This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.
14 RES# I This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
15 D/C# I This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When serial interface is selected, this pin must be connected to VSS.
16 R/W#(WR#) I This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E(RD#) I This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID and D2 will be the serial data output: SOD.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I This pin is the segment output current reference pin.
IREF is supplied externally.
A resistor should be connected between this pin and VSS to maintain current of around 15uA.
27 ROM0 I These pins are used to select Character ROM; select appropriate logic setting as described in the following table. ROM1 and ROM0 are pin select as shown in below table:
Character ROM selection
ROM1 ROM0 ROM
0 0 A
0 1 B
1 0 C
1 1 S/W selectable(3)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
28 ROM1
29 OPR0 I This pin is used to select the character number of character generator.
Character RAM selection
OPR1 OPR0 CGROM CGRAM
1 1 256 0
0 1 248 8
1 0 250 6
0 0 240 8

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
30 OPR1
31 VCOMH P COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
32 VCC P Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
33 NC No connection

规格说明

项目 尺寸 单位
字符数 20字x4行
模块尺寸 84.5 x 27.5 x 2.17 mm
检视区域 72.42 x 22.82 mm
有效区域 70.42 x 20.82 mm
点大小 0.57 x 0.57 mm
点间距 0.60 x 0.60 mm
字大小 2.97 x 4.77 mm
字间距 3.55 x 5.35 mm
LCD类型 OLED, 单色
Duty 1/32
IC SSD1311
界面 6800,8080,SPI,I2C
尺寸 2.89 寸

最大绝对额定值

项目 符号 最小值 最大值 单位
逻辑电源电压 VDD -0.3 VDDIO V
输入/输出针脚(Pin)电源 VDDIO -0.3 6 V
工作电压 VCC 0 16 V
工作温度 TOP -40 +80 °C
储存温度 TST -40 +85 °C
 

电气特性

DC 电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VDD Low Voltage I/O 2.4 3.0 3.3 V
5V I/O
(VDD as output)
V
输入/输出针脚(Pin)电源 VDDIO Low Voltage I/O 2.4 3.0 3.3 V
5V I/O 4.4 5.0 5.3 V
工作电压 VCC 8.0 10.0 10.5 V
8.0 12.0 12.5 V
输入高电压 VIH 0.8xVDDIO V
输入低电压 VIL 0.2xVDDIO V
输出高电压 VOH IOH=-0.5mA 0.9xVDDIO V
输出低电压 VOL IOL=0.5mA 0.1xVDDIO V
50%显示画面耗电流 ICC VCC=10V 19 29 mA
VCC=12V 23 35 mA

可选FPC :

图示 FPC长度 PIN pitch ZIF FPC or HOTBAR FPC 接口 FPC No. Create Date
FPC2070003111XXXXX00_WEO002004CLPP5N00000 35.2 31 0.7 BOTBAR FPC 6800,8080,SPI,I2C FPC2070003111XXXXX00 20120921
FPC2005003421XXXXX00_WEO002004CLPP5N00001 31 34 0.5 ZIF FPC 6800,8080,SPI,I2C FPC2005003421XXXXX00 20151223

Search keyword: oled 20x4, 20x4 oled

推荐产品

go top
close

我们重视您的隐私

通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。

我们重视您的隐私

Winstar 及部分第三方在 www.winstar.com.tw 上使用 cookies。关于 cookie 的种类、用途及相关第三方的详细信息,请参见下文及我们的《Cookie 政策》。请点击“允许全部”来同意我们使用 cookies,以确保您在我们网站上获得最佳体验。您也可以设置您的偏好或拒绝 cookies(必要的 cookies 除外)。

管理同意声明

永久启用
必要的 Cookie

这些 Cookie 是必不可少的,以便让您在浏览网站并使用其功能上有更好地体验,例如设置您的隐私偏好、登录或填写窗体。

分析 Cookie

这些也被称为「统计cookie」,用于收集您使用网站的信息,例如您访问了哪些页面以及点击了哪些连结。查看详细信息