首页 产品介绍 OLED显示屏 图形 OLED 显示屏 WEO012832D

0.91寸OLED显示器模块,被动矩阵式OLED 12832

型号 WEO012832D

►2017年台湾精品奖获奖产品
►类型:图形OLED (不含铁框)
►结构:COG
►尺寸:0.91寸;适用于穿载设备
►128 x 32点阵
►IC:SSD1306
►3V电源电压
►1/32 duty
►接口:SPI
►发光颜色: 白色 / 黄色 / 天空蓝
►其它FPC选项请参阅最下方表格说明

产品叙述

0.91寸OLED显示器模块是最常被采用作为穿戴式显示器的PM OLED(被动矩阵式OLED)小尺寸之一。华凌WEO012832D荣获2017台湾精品奖是市场上最受欢迎的COG图形0.91寸 OLED模块;分辨率为128x32 像素,外形尺寸为30×11.5 mm,AA有效区域尺寸为22.384×5.584 mm。此款内置SSD1306 IC,模块控制接口仅能使用串列式4线 SPI。因为是OLED面板无需背光源,此款使用COG工艺,所以显示器模块非常的薄仅1.26 mm,重量轻且低耗电流,超高对比度且视角超过175度,所以非常适合手持式产品、量测仪器、智慧电表、穿戴式产品、电子烟、物联网设备等等。 COG OLED与TAB OLED有个很重要的差异是因为COG模块的IC是打在玻璃上,因此COG OLED 模块的FPC多半是可以饶折的,因而在客户端的产品设计上较为方便。此型号OLED模块可支持内部升压及外部供电。


     可选 FPC

 

规格图

OLED 128x32, 128x32 OLED Display, 0.91 inch OLED - WEO012832D

Data source ref: WEO012832DWPP3N00008
 

产品规格

Pin功能定义

No. 符号 功能说明
1 C2P Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2N
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
7 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
8 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 D/C# Data/Command Control
This pin is Data/Command control pin..
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register.
11 SCLK When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
12 SDIN
13 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA.
14 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
15 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

规格说明

项目 规格 单位
点阵(分辨率) 128 × 32 Dots
模块尺寸 30.0 × 11.5 × 1.26 mm
有效区域 22.384 × 5.584 mm
像素大小 0.152 × 0.152 mm
像素间距 0.175 × 0.175 mm
显示模式 Passive Matrix被动矩阵
发光颜色 单色
驱动方式 1/32 Duty
IC SSD1306
界面 4线SPI
尺寸(对角线) 0.91 寸

最大绝对额定值

参数 符号 最小值 最大值 单位
逻辑电源电压 VDD 0 4.0 V
显示电源电压 VCC 0 16.0 V
工作温度 TOP -40 +80 °C
储存温度 TSTG -40 +85 °C

电气特性

DC 电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VDD 2.8 3.0 3.3 V
显示电源电压 (Supplied Externally) VCC 7 7.25 8 V
电荷帮浦稳压器电源电压 VBAT 3.0 4.2 V
显示器的电荷帮浦输出电压 (Generated by Internal DC/DC) Charge Pump
VCC
7.0 7.5 - V
输入高准位 VIH 0.8×VDD VDD V
输入低准位 VIL 0 0.2×VDD V
输出高准位 VOH 0.9×VDD VDD V
输出低准位 VOL 0 0.1×VDD V
VCC的工作电流 (VCC Supplied Externally) ICC VCC =7.25V 7 11 mA
550%显示画面耗电流 (VCC Generated by Internal DC/DC) IBAT 15 25 mA

FPC Options:

Drawing FPC Length PIN pitch ZIF FPC or HOTBAR FPC Interface FPC No. Create Date
FPC2065001501XXXXX00_WEO012832DLPP3N00000 17.06 15 0.65 HOTBAR FPC SPI FPC2065001501XXXXX00 20140827
FPC2050001511XXXXX02_WEO012832DWPP3N00001 40.76 15 0.5 ZIF FPC SPI FPC2050001511XXXXX02 20150421
FPC2062001401XXXXX02_WEO012832FLPP3N00000 11.26 14 0.62 HOTBAR FPC I2C FPC2062001401XXXXX02 20160106

Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91寸 oled, oled 0.91, oled 0.91"
go top
close