Pantalla OLED (Diodos Orgánicos) 0,91 pulgada, 128x32 puntos
Modelo Nº WEO012832D
►2017 Taiwan Excellence Award
►Tipo: Gráfico (sin marco)
►Estructura: COG
►Tamaño : 0.91"
►Suitable for wearable device
►Matriz de puntos 128 x 32
►IC:SSD1306
►Fuente de alimentación de 3V
►1/32 duty
►Interfaz: SPI
►Color de la pantalla: Blanco / Amarillo / Azul cielo
►Otras opciones de FPC disponibles en la siguiente tabla.
Descripción
WEO012832D es un modulo display OLED de 128x32 con un tamaño diagonal de 0,91 pulgadas. Este modelo tiene un tamaño de 30,0 x 11,5 mm y un tamaño de área activa de 22,384 × 5,584 mm. Este módulo es compatible con la interfaz SPI de 4 cables. El voltaje de suministro para la lógica es de 2,8 V a 3,3 V, con un valor típico de 3,0 V, con 1/32 de servicio de impulsión. una relación de contraste de 2,000:1.
Esta serie de modulo display OLED 128x32 puede funcionar a temperaturas de -40 ℃ a +80 ℃ y su temperatura de almacenamiento oscila entre -40 ℃ y +85 ℃.
Este módulo es una pantalla OLED COG de tamaño pequeño ultradelgada, ligera y tiene un bajo consumo de energía. Es muy adecuada para aplicaciones de hogar inteligente, dispositivos médicos, dispositivos portátiles, dispositivos ponibles.
Opciones de FPC
DIBUJO
Data source ref: WEO012832DWPP3N00008
ESPECIFICACIONES
Función interfaz Pin
No. | Símbolo | Función |
---|---|---|
1 | C2P | Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost CapacitorThe charge-pump capacitors are required between the terminals. They must be floated when the converter is not used. |
2 | C2N | |
3 | C1P | |
4 | C1N | |
5 | VBAT | Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used. |
6 | VSS | Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground. |
7 | VDD | Power Supply for Logic This is a voltage supply pin. It must be connected to external source. |
8 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
9 | RES# | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
10 | D/C# | Data/Command Control This pin is Data/Command control pin.. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. |
11 | SCLK | When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
12 | SDIN | |
13 | IREF | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA. |
14 | VCOMH | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
15 | VCC | Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used. |
Especificaciones generales
Elemento | Dimensión | Unidad |
---|---|---|
Matriz de puntos (Resolución) | 128 × 32 | puntos |
Dimensión del módulo | 30.0 × 11.5 × 1.26 | mm |
zona activa | 22.384 × 5.584 | mm |
Tamaño del punto | 0.152 × 0.152 | mm |
Distancia entre puntos | 0.175 × 0.175 | mm |
Modo de visualización | Matriz pasiva | |
Color de la pantalla | Monocromos | |
Drive Duty | 1/32 Duty | |
IC | SSD1306 | |
Interfaz | 4-wire SPI | |
Tamaño (Diagonal) | 0.91 pulgada |
Valores nominales máximos absolutos
Parameter | Símbolo | Valor mín. | Valor máx. | Unidad |
---|---|---|---|---|
Supply Voltage for Logic | VDD | 0 | 4.0 | V |
Supply Voltage for Display | VCC | 0 | 16.0 | V |
Temperatura de funcionamiento | TOP | -40 | +80 | °C |
Temperatura de almacenamiento | TSTG | -40 | +85 | °C |
Características electrónicas
DC Características electrónicas
Elemento | Símbolo | Condición | Valor mín. | Valor típico | Valor máx. | Unidad |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display (Supplied Externally) | VCC | - | 7 | 7.25 | 8 | V |
Charge Pump Regulator Supply Voltage | VBAT | - | 3.0 | - | 4.2 | V |
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) | Charge Pump VCC |
- | 7.0 | 7.5 | - | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | 0 | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.9×VDD | - | VDD | V |
Output Low Volt. | VOL | - | 0 | - | 0.1×VDD | V |
Operating Current for VCC (VCC Supplied Externally) | ICC | VCC =7.25V | - | 7 | 11 | mA |
Display 50% Pixel on (VCC Generated by Internal DC/DC) | IBAT | - | - | 15 | 25 | mA |
Opciones de FPC:
Dibujo | FPC Length | PIN | pitch | ZIF FPC or HOTBAR FPC | Interfaz | FPC No. | Create Date |
---|---|---|---|---|---|---|---|
17.06 | 15 | 0.65 | HOTBAR FPC | SPI | FPC2065001501XXXXX00 | 20140827 | |
40.76 | 15 | 0.5 | ZIF FPC | SPI | FPC2050001511XXXXX02 | 20150421 | |
11.26 | 14 | 0.62 | HOTBAR FPC | I2C | FPC2062001401XXXXX02 | 20160106 |
Search keyword: 128x32 oled, oled 128x32, 0.91 oled, 0.91" oled, 0.91 pulgada oled, oled 0.91, oled 0.91"