Strona główna Produkty Wyświetlacz OLED Graficzne Wyświetlacz OLED WEO016080A

Moduł wyświetlacza OLED SSD1320 1,54 cala 160x80

Numer modelu WEO016080A

►Typ: graficzny
►Struktura: COG
►Rozmiar: 1.54"
►160x80 matryca punktowa
►IC:SSD1320
►zasilanie 3V
►wypełnienie 1/80
►Interfejs: 6800, 8080, SPI, I2C
►Kolor wyświetlacza: biały
►Support Grayscale

Opis

WEO016080A to 1.54-calowy graficzny wyświetlacz OLED typu COG o rozdzielczości 160x80 pikseli. Moduł ma wymiary 43.5 x 22.5 mm, aktywna powierzchnia wynosi 35.02 x 17.50 mm, a jego smukła profilowa grubość 1.41 mm jest efektem struktury COG.

Wyposażony w układ SSD1320, moduł obsługuje interfejsy 6800/8080 8-bit, 4-przewodowy SPI i I2C. Oferuje 4-bit (16 Levels) skalę szarości i osiąga imponujący stosunek kontrastu wynoszący 10000:1.

Praca modułu jest możliwa w zakresie napięcia zasilania logicznego od 1.65V do 3.3V (zwykle 3.0V), przy temperaturach pracy od -40°C do +80°C i możliwości przechowywania od -40°C do +85°C.

Idealny do różnorodnych zastosowań, takich jak produkty sieciowe, testery USB, smartwatche, klawiatury do gier oraz inteligentne urządzenia zdrowotne, jak np. oksymetry i analizatory skóry, WEO016080A poprawia jakość wyświetlania dzięki wyraźnemu i dynamicznemu ekranowi.

Dzięki wysokiej rozdzielczości (160x80 pikseli) i niskiemu poborowi mocy ten moduł wyświetlacza OLED doskonale nadaje się do aplikacji wymagających wysokiej wydajności i efektywności.

 

Moduł wyświetlacza OLED SSD1320 1,54 cala 160x80 - WEO016080A

Rysunek

1.54 inch 160x80 SSD1320 OLED Display Module - WEO016080A

Data source ref:WEO016080AWPP3N00000

Specyfikacja

Dane mechaniczne

Rzecz Wymiar Jednostka
Matryca punktowa 160 x 80 punktów
Wymiary modułu 43.5 x 22.5 x 1.41 mm
Obszar aktywny 35.02 x 17.50 mm
Wielkość piksela 0.199 x 0.199 mm
Raster pomiędzy pikselami 0.219 x 0.219 mm
Tryb wyświetlania matryca
Kolor wyświetlacza Monochromatyczny
Drive Duty 1/80 Duty
Skala szarości 4 bits
Interfejs 6800,8080,4-Wire SPI,I2C
IC SSD1320
Rozmiar 1.54 cale

Bezwzględne oceny maksymalne

Parameter Symbol Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 19 V
Temperatura pracy TOP -40 +80 °C
Temperatura przechowywania TSTG -40 +85 °C

Parametry elektryczne

DC Parametry elektryczne

Rzecz Symbol Stan Minimalna wartość Typowa wartość Maksymalna wartość Jednostka
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Supply Voltage for Display VCC 8.0 15.0 15.5 V
High Level Input VIH 0.8×VDD VDD V
Low Level Input VIL 0 0.2×VDD V
High Level Output VOH 0.9×VDD VDD V
Low Level Output VOL 0 0.1×VDD V
VCC Supply Current ICC VDD=3V,VCC=15V
Display 50% Pixel ON
14 21 mA

Funkcja pinów interfejsu

No. Symbol Funkcja
1 N.C.
(GND)
Reserved Pin (Supporting Pin)
The supporting pin can reduce the influences from stresses on the function pins.
This pin could be connected to external ground as the ESD protection circuit.
2 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. It must be connected to external source.
3~4 N.C. Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.
5 BS1 Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
  BS1 BS2
I2C 1 0
4-wire SPI 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1
6 BS2
7 VSS Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.
8 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current at 10μA maximum.
9 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
10 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation.
11 D/C# Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at
D7~D0 is treated as display data. When the pin is pulled low, the input at
D7~D0 will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
12 R/W# Read/Write Select or Write
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as
Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input.
Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
13 E/RD# Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the
Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.
14 D0 Host Data Input/Output Bus
These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D2, D1 should be tied together as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,
SDAin in application and D0 is the serial clock input, SCL.
15 D1
16 D2
17 D3
18 D4
19 D5
20 D6
21 D7
22 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
23 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS.
24 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. It must be connected to external source.

Produkty powiązane

go top
close

Cenimy twoją prywatność

Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności

Cenimy twoją prywatność

Winstar i niektóre strony trzecie używają plików cookie na stronie www.winstar.com.tw. Szczegóły dotyczące rodzajów plików cookie, ich celu oraz zaangażowanych stron trzecich są opisane poniżej i w naszej Polityce plików cookie. Kliknij „Zezwól na wszystko”, aby wyrazić zgodę na korzystanie z plików cookie i uzyskać najlepsze możliwe wrażenia na naszych stronach internetowych. Możesz także ustawić preferencje lub odrzucić pliki cookie (z wyjątkiem niezbędnych plików cookie).

Zarządzaj preferencjami zgody

Zawsze aktywne
Niezbędne pliki cookie

Te ciasteczka są niezbędne, aby umożliwić Ci poruszanie się po stronie internetowej i korzystanie z jej funkcji, takich jak ustawianie preferencji prywatności, logowanie się lub wypełnianie formularzy.

Ciasteczka analityczne

Te pliki cookie, znane również jako „ciasteczka statystyczne”, zbierają informacje o tym, jak korzystasz z witryny, takie jak które strony odwiedziłeś i które linki kliknąłeś. Zobacz szczegóły.