1.54 inç 160x80 SSD1320 OLED Ekran Modülü - WEO016080A

1.54 inç 160x80 SSD1320 OLED Ekran Modülü

Model No. WEO016080A

►Türü : Grafik
►Yapı : COG
►Boyut : 1.54 inch
►160x80 dot matrisi
►IC：SSD1320
►3V güç sağlayıcı
►1/80 görev
►Ara yüz : 6800, 8080, SPI, I2C
►OLED Rengi: Beyaz
►Gri Tonlama Desteği

PDF İndir

DEMO CODE Sorguya ekle

Önceki Listeye geri dön Sonraki

Açıklama

WEO016080A, 160x80 noktalı bir çözünürlüğe sahip 1.54 inç COG grafik OLED ekranıdır. 43.5 x 22.5 mm ölçülerinde ve 35.02 x 17.50 mm aktif alanıyla, COG yapısına sahip ince profili 1.41 mm'e kadar incelmiştir.

SSD1320 IC ile donatılan bu modül, 6800/8080 8-bit, 4-tel SPI ve I2C arabirimlerini destekler. 4-bit (16 Levels) gri tonlama sunar ve 10000:1 etkileyici kontrast oranına ulaşır.

Mantık güç besleme voltajı 1.65V ile 3.3V arasında değişen (tipik olarak 3.0V), modül -40°C ile +80°C arasında güvenilir bir şekilde çalışırken, -40°C ile +85°C arası depolama kapasitesine sahiptir.

Ağ Ürünleri, USB Test Cihazları, Akıllı Saatler, Oyun Klavyeleri ve oksimetreler ve cilt analiz cihazları gibi Akıllı Sağlık Cihazları da dahil olmak üzere çeşitli uygulamalar için ideal olan WEO016080A, net ve canlı ekranıyla görüntü kalitesini arttırır.

Yüksek çözünürlüğü (160x80 piksel) ve düşük güç tüketimi ile bu OLED ekran modülü, performans odaklı ve verimli uygulamalar için mükemmel bir seçenektir.

1.54 inç 160x80 SSD1320 OLED Ekran Modülü - WEO016080A

ÇIZIM

1.54 inch 160x80 SSD1320 OLED Display Module - WEO016080A

Data source ref:WEO016080AWPP3N00000

AYRINTILAR

Mekanik Veri

Kalem	Ölçü	Birim
Nokta Matrisi	160 x 80 Dots	－
Modül ölçüleri	43.5 x 22.5 x 1.41	mm
Aktif alan	35.02 x 17.50	mm
Nokta boyutu	0.199 x 0.199	mm
Nokta sıklığı	0.219 x 0.219	mm
Display Mode	Pasif Matrisli
Display Color	Monokrom
Drive Duty	1/80 Duty
Gray Scale	4 bits
Arayüz	6800,8080,4-Wire SPI,I2C
IC	SSD1320
Boyut	1.54 inç

Maksimum Değerler

Parameter	Sembol	Minumum Deger	Tipik Deger	Maksimum Deger	Birim
Supply Voltage for Logic	VDD	-0.3	－	4	V
Supply Voltage for Display	VCC	0	－	19	V
Çalışma Sıcaklığı	TOP	-40	－	+80	°C
Saklama Sıcaklığı	TSTG	-40	－	+85	°C

Elektronik Özellikleri

DC Elektronik Özellikleri

Kalem	Sembol	Durum	Minumum Deger	Tipik Deger	Maksimum Deger	Birim
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Supply Voltage for Display	VCC	－	8.0	15.0	15.5	V
High Level Input	VIH	－	0.8×VDD	－	VDD	V
Low Level Input	VIL	－	0	－	0.2×VDD	V
High Level Output	VOH	－	0.9×VDD	－	VDD	V
Low Level Output	VOL	－	0	－	0.1×VDD	V
VCC Supply Current	ICC	VDD=3V,VCC=15V Display 50% Pixel ON	－	14	21	mA

Arayüz Pin Fonksiyonlari

No.

Sembol

Fonksiyon

N.C.
(GND)

Reserved Pin (Supporting Pin)
The supporting pin can reduce the influences from stresses on the function pins.
This pin could be connected to external ground as the ESD protection circuit.

VCC

Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. It must be connected to external source.

3~4

N.C.

Reserved Pin
The N.C. pin between function pins are reserved for compatible and flexible design.

BS1

Communicating Protocol Select
These pins are MCU interface selection input. See the following table:

	BS1	BS2
I2C	1	0
4-wire SPI	0	0
8-bit 68XX Parallel	0	1
8-bit 80XX Parallel	1	1

BS2

VSS

Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.

IREF

Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current at 10μA maximum.

CS#

Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.

RES#

Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation.

D/C#

Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at
D7~D0 is treated as display data. When the pin is pulled low, the input at
D7~D0 will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.

R/W#

Read/Write Select or Write
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as
Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
When 80XX interface mode is selected, this pin will be the Write (WR#) input.
Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

E/RD#

Read/Write Enable or Read
This pin is MCU interface input.
When interfacing to a 68XX-series microprocessor, this pin will be used as the
Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
When serial mode is selected, this pin must be connected to VSS.

Host Data Input/Output Bus
These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D2, D1 should be tied together as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,
SDAin in application and D0 is the serial clock input, SCL.

VDD

Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.

VCOMH

Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS.

VCC