私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
型番 WFN0200A2T07ADNN000
►2インチ TFT
►解像度: 240 x 320 dots
►視野角: IPS
►インターフェース: MCU/SPI+RGB
►駆動IC:ST7789
►コントロールボード: 無
►輝度(cd/m²): 260
►スルーホールフレーム: 無
►タッチパネル: 無
WFN0200A2T07ADNN000 は、透過型と反射型の表示モードを組み合わせた先進の 半透過型スクリーン(Transflective screen) 技術を採用し、さまざまな照明条件下でも視認性を大幅に向上させます。2インチ縦型レイアウトと IPS 広視野角により、屋外およびポータブルデバイス用途に最適です。
項目 | 仕様 | 単位 |
---|---|---|
サイズ (対角線) | 2 | インチ |
ドットマトリックス(解像度) | 240 × RGB × 320(TFT) | dots |
外形寸法 | 35.8 × 52.1 × 2.65 | mm |
有効エリア | 30.60 × 40.80 | mm |
ドットピッチ | 0.1275 × 0.1275 | mm |
LCDタイプ | TFT・ノーマリ・ブラック・透過型 | |
視野角度 | 80/80/80/80 | |
TFT インターフェイス | 3/4serial 8/9/16/18bit MCU 3/4SPI+16/18BIT RGB |
|
バックライトタイプ | LED・ノーマリ・ホワイト | |
ドライバIC | ST7789或いは互換性コントローラー | |
タッチパネル | タッチパネル無し | |
表面処理 | グレア |
項目 | 記号 | 最小値 | 標準値 | 最大値 | 単位 |
---|---|---|---|---|---|
操作温度 | TOP | -20 | - | +70 | ℃ |
保存温度 | TST | -30 | - | +80 | ℃ |
項目 | 記号 | 最小値 | 標準値 | 最大値 | 単位 |
---|---|---|---|---|---|
デジタル供給電圧 | VCI | 2.5 | 3.3 | 3.6 | V |
デジタルインターフェース電源電圧 | IOVCC | 1.65 | 1.8 | 3.3 | V |
ノーマルモード動作電流 | IDD | -- | 6 | 12 | mA |
入力電圧レベル | VIH | 0.7IOVCC | IOVCC | V | |
VIL | GND | 0.3IOVCC | V | ||
出力電圧レベル | VOH | 0.8IOVCC | IOVCC | V | |
VOL | GND | 0.2IOVCC | V |
項目 | 記号 | 最小値 | 標準値 | 最大値 | 単位 |
---|---|---|---|---|---|
LED電流 | - | 60 | 80 | - | mA |
LED電圧 | VLED+ | 2.8 | 3.2 | 3.3 | V |
LEDの寿命 | - | 50,000 | - | - | Hr |
Pin No | 記号 | 功能 | I/O |
---|---|---|---|
1 | GND | Ground. | P |
2 | VCI | Supply voltage (3.3V). | P |
3 | IOVCC | Supply voltage (1.65-3.3V). | P |
4 | IM2 | MPU Parallel interface bus and serial interface select If use RGB Interface must select serial interface. Fix this pin at IOVCC and GND. |
I |
5 | IM1 | ||
6 | IM0 | ||
7 | RESET | This signal will reset the device and must be applied to properly initialize the chip. |
I |
8 | CS | Chip select input pin (“Low” enable). fix this pin at GND when not in use. |
I |
9 | DC(SPI-SCL) | -Display data/command selection pin in parallel interface. -This pin is used to be serial interface clock. DC=’1’: display data or parameter. DC=’0’: command data. -If not used, please fix this pin at GND. |
I |
10 | WR(SPI-RS) | -Write enable in MCU parallel interface. Display data/command selection pin in 4-line serial interface. Second Data lane in 2 data lane serial interface. -If not used, please fix this pin at GND. |
I |
11 | RD | Serves as a read signal and MCU read data at the rising edge. fix this pin at IOVCC or GND when not in use. |
I |
12 | VSYNC | Frame synchronizing signal for RGB interface operation. fix this pin at GND when not in use. |
I |
13 | HSYNC | Line synchronizing signal for RGB interface operation. fix this pin at GND when not in use. |
I |
14 | ENABLE | Data enable signal for RGB interface operation. fix this pin at GND when not in use. |
I |
15 | DOTCLK | Dot clock signal for RGB interface operation. Fix this pin at GND when not in use. |
I |
16 | SDA | Serial input signal. The data is latched on the rising edge of the SCL signal. fix this pin at GND when not in use. |
I |
17-34 | DB0-DB17 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode . Fix to GND level when not in use |
I/0 |
35 | SDO | SPI interface output pin. -The data is output on the falling edge of the SCL signal. -If not used, let this pin open. |
O |
36 | LEDA | Anode pin of backlight | P |
37 | LEDK1 | Cathode pin OF backlight | P |
38 | LEDK2 | Cathode pin OF backlight | P |
39 | LEDK3 | Cathode pin OF backlight | P |
40 | LEDK4 | Cathode pin OF backlight | P |
41 | XR(NC) | Touch panel Right Glass Terminal | A/D |
42 | YU(NC) | Touch panel Top Film Terminal | A/D |
43 | XL(NC) | Touch panel LEFT Glass Terminal | A/D |
44 | YD(NC) | Touch panel Bottom Film Terminal | A/D |
45 | GND | Ground. | P |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー