Display LCD COG Gráfico de 240x128
Model No. WO240128A
►LCD COG
►Módulo Display LCD Gráfico
►240 x 128 pontos
►IC: UC1608
►Alimentação +3V
►1/128 duty cycle
►Interface : 6800/8080/SPI
DRAWING
Data source ref:WO240128A-TFH#
SPECIFICATIONS
Função do pino de interface
Pin No. | Símbolo | Level | DESCRIÇÃO | |||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VB1- | PWR | LCD Bias Voltages. These are the voltage source to provide SEG driving currents. These voltages are generated internally. Connect capacitors of CBX between VBX+ and VBX–. The resistance of these four traces directly affects the SEG driving strength of the resulting LCD module. Minimize the trace resistance is critical in achieving high quality image. |
|||||||||||||||||||||||||||||||||||||||||||||
2 | VB1+ | |||||||||||||||||||||||||||||||||||||||||||||||
3 | VB0- | |||||||||||||||||||||||||||||||||||||||||||||||
4 | VB0+ | |||||||||||||||||||||||||||||||||||||||||||||||
5 | VLCD | PWR | Main LCD Power Supply. Connect these pins together. | |||||||||||||||||||||||||||||||||||||||||||||
6 | VBIAS | I | This is the reference voltage to generate the actual SEG driving voltage. VBIAS can be used to fine tune VLCD by external variable resistors. Internal resistor network has been provided to simplify external trimming circuit. In COF application, connect a small bypass capacitor between VBIAS and VSS to reduce noise. |
|||||||||||||||||||||||||||||||||||||||||||||
7 | VSS | PWR | Ground | |||||||||||||||||||||||||||||||||||||||||||||
8 | VDD | PWR | Supply Voltage for logic | |||||||||||||||||||||||||||||||||||||||||||||
9 | D7 | I/O | Bi-directional bus for both serial and parallel host interfaces. In serial modes, connect D[0] to SCK, D[3] to SDA,
|
|||||||||||||||||||||||||||||||||||||||||||||
10 | D6 | |||||||||||||||||||||||||||||||||||||||||||||||
11 | D5 | |||||||||||||||||||||||||||||||||||||||||||||||
12 | D4 | |||||||||||||||||||||||||||||||||||||||||||||||
13 | D3 | |||||||||||||||||||||||||||||||||||||||||||||||
14 | D2 | |||||||||||||||||||||||||||||||||||||||||||||||
15 | D1 | |||||||||||||||||||||||||||||||||||||||||||||||
16 | D0 | |||||||||||||||||||||||||||||||||||||||||||||||
17 | WR1 | I | WR[1:0] controls the read/write operation of the host interface. See Host Interface section for more detail. In parallel mode, WR[1:0] meaning depends on whether the interface is in the 6800 mode or the 8080 mode. In serial interface modes, these two pins are not used, connect them to VSS. |
|||||||||||||||||||||||||||||||||||||||||||||
18 | WR0 | |||||||||||||||||||||||||||||||||||||||||||||||
19 | CD | I | Select Control data or Display data for read/write operation. In S9 mode, CD pin is not used. Connect CD to VSS when not used. ”L”: Control data ”H”: Display data | |||||||||||||||||||||||||||||||||||||||||||||
20 | RST | I | When RST=”L”, all control registers are re-initialized by their default states. Since UC1608x has built-in Power-ON-Reset and Software Reset command, RST pin is not required for proper chip operation. When RST is not used, connect the pin to VDD. |
|||||||||||||||||||||||||||||||||||||||||||||
21 | CS | I | Chip Select. The chip is selected when CS=”H”. When the chip is not selected, D[7:0] will be high impedance. | |||||||||||||||||||||||||||||||||||||||||||||
22 | BM0 | I | Bus mode: The interface bus mode is determined by BM[1:0] and D[7:6] by the following relationship:
|
|||||||||||||||||||||||||||||||||||||||||||||
23 | BM1 |
Dados Mecânicos
Item | Dimensão | Unidade |
---|---|---|
Formato do display | 240 x 128 pontos | - |
Dimensão do módulo | 98.7 x 67.7 x 9.5 (Max) | mm |
View area | 92.0 x 53.0 | mm |
Área ativa | 83.975 x 44.775 | mm |
Tamanho do ponto | 0.325 x0.325 | mm |
Distância entre pontos | 0.35 x 0.35 | mm |
Duty | 1/128 , 1/12 Bias | |
Tipo de luz de fundo | LED | |
IC | UC1608 | |
Interface | 6800/8080/3 wire SPI/4 wire SPI |
Classificações Máximas Absolutas
Item | Símbolo | Min | Típico | Máximo | Unidade |
---|---|---|---|---|---|
Temperatura de operação | TOP | -20 | - | +70 | ℃ |
Temperatura de armazenamento | TST | -30 | - | +80 | ℃ |
Supply voltage for Logic | VDD | -0.3 | - | +4.0 | V |
LCD Generator supply voltage | VDD2 | -0.3 | - | +4.0 | V |
LCD Generated voltage | VLCD | -0.3 | - | +17.8 | V |
Características Eletrônicas
Item | Símbolo | Condition | Min | Típico | Máximo | Unidade |
---|---|---|---|---|---|---|
Supply Voltage For Logic | VDD-VSS | - | 2.7 | 2.8~3.3 | 3.6 | V |
Supply Voltage For LCM | V0-VSS | Ta=-20℃ Ta=25℃ Ta=70℃ |
- 15.2 - |
- 15.5 - |
- 15.8 - |
V V V |
Input High Volt. | VIH | - | 0.8 VDD | - | - | V |
Input Low Volt. | VIL | - | - | - | 0.2VDD | V |
Output High Volt. | VOH | - | 0.8VDD | - | - | V |
Output Low Volt. | VOL | - | - | - | 0.2VDD | V |
Supply Current(No include LED Backlight) | IDD | VDD=3.0V | - | 1.1 | - | mA |
Search keyword: 240x128 lcd, 240 x 128 lcd, lcd 240x128, lcd 240 x 128