Écran LCD COG 240x128 avec UC1608 - WO240128A

Écran LCD COG 240x128 avec UC1608

N° de modèle WO240128A

►Afficheur COG
►Afficheur graphique
►240 x 128 points
►IC: UC1608
►Alimentation +3V
►Taux de rafraichissement 1/128 duty cycle
►Interface : 6800/8080/SPI

Téléchargement PDF

DEMO CODE Ajouter à demande

PRÉC. Retour à la liste SUIVANT

DESSIN

COG LCD Display 240x128 - Winstar WO240128A

Data source ref:WO240128A-TFH#

SPÉCIFICATIONS

Fonction PIN sur l'interface

Pin No.

Symbole

Level

Description

VB1-

PWR

LCD Bias Voltages. These are the voltage source to provide SEG driving currents. These voltages are generated internally. Connect capacitors of CBX between VBX+ and VBX–.
The resistance of these four traces directly affects the SEG driving strength of the resulting LCD module. Minimize the trace resistance is critical in achieving high quality image.

VB1+

VB0-

VB0+

VLCD

PWR

Main LCD Power Supply. Connect these pins together.

VBIAS

This is the reference voltage to generate the actual SEG driving voltage. VBIAS can be used to fine tune VLCD by external variable resistors. Internal resistor network has been provided to simplify external trimming circuit.
In COF application, connect a small bypass capacitor between VBIAS and VSS to reduce noise.

VSS

PWR

Ground

VDD

PWR

Supply Voltage for logic

I/O

Bi-directional bus for both serial and parallel host interfaces.
In serial modes, connect D[0] to SCK, D[3] to SDA,

	BM=1x (Parallel)	BM=0x (Parallel)	BM=01 (S9)	BM=00 (S8/S8uc)
D0	D0	D0/D4	SCK	SCK
D1	D1	D1/D5	-	-
D2	D2	D2/D6	-	-
D3	D3	D3/D7	SDA	SDA
D4	D4	-	-	-
D5	D5	-	-	-
D6	D6	-	S9	S8/S8uc
D7	D7	0	1	1

Connect unused pins to VDD or VSS.

WR1

WR[1:0] controls the read/write operation of the host interface. See Host Interface section for more detail.
In parallel mode, WR[1:0] meaning depends on whether the interface is in the 6800 mode or the 8080 mode. In serial interface modes, these two pins are not used, connect them to VSS.

WR0

Select Control data or Display data for read/write operation. In S9 mode, CD pin is not used. Connect CD to VSS when not used. ”L”: Control data ”H”: Display data

RST

When RST=”L”, all control registers are re-initialized by their default states.
Since UC1608x has built-in Power-ON-Reset and Software Reset command, RST pin is not required for proper chip operation. When RST is not used, connect the pin to VDD.

Chip Select. The chip is selected when CS=”H”. When the chip is not selected, D[7:0] will be high impedance.

BM0

Bus mode: The interface bus mode is determined by BM[1:0] and D[7:6] by the following relationship:

BM[1:0]	D[7:6]	Mode
11	Data	6800/8-bit
10	Data	8080/8-bit
1	0X	6800/8-bit
0	0X	8080/8-bit
1	10	3-wire SPI w/9-bit token (S9: conventionl)
0	10	4-wire SPI w/8-bit token (S8: conventionl)
0	11	3- or 4-wire SPI w/8-bit token (S8uc: Ultra-Compact)

BM1

Données mécaniques

Article	Dimensions	Unité
Format d'affichage	240 x 128 points	－
Dimensions du module	98.7 x 67.7 x 9.5 (Max)	mm
Zone d'affichage	92.0 x 53.0	mm
Zone active	83.975 x 44.775	mm
Taille des points	0.325 x0.325	mm
Pas des points	0.35 x 0.35	mm
Duty	1/128 , 1/12 Bias
Type de rétroéclairage	LED
IC	UC1608
Interface	6800/8080/3 wire SPI/4 wire SPI

Valeurs nominales maximales absolues

Article	Symbole	Min	Typ	Max	Unité
Température de fonctionnement	TOP	-20	－	+70	℃
Température de stockage	TST	-30	－	+80	℃
Supply voltage for Logic	VDD	-0.3	－	+4.0	V
LCD Generator supply voltage	VDD2	-0.3	－	+4.0	V
LCD Generated voltage	VLCD	-0.3	－	+17.8	V

Caractéristiques électroniques

Article	Symbole	État	Min	Typ	Max	Unité
Supply Voltage For Logic	VDD-VSS	－	2.7	2.8~3.3	3.6	V
Supply Voltage For LCM	V0-VSS	Ta=-20℃ Ta=25℃ Ta=70℃	－ 15.2 －	－ 15.5 －	－ 15.8 －	V V V
Input High Volt.	VIH	－	0.8 VDD	－	－	V
Input Low Volt.	VIL	－	－	－	0.2VDD	V
Output High Volt.	VOH	－	0.8VDD	－	－	V
Output Low Volt.	VOL	－	－	－	0.2VDD	V
Supply Current(No include LED Backlight)	IDD	VDD=3.0V	－	1.1	－	mA

Search keyword: 240x128 lcd, 240 x 128 lcd, lcd 240x128, lcd 240 x 128