우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
모델 번호 WEA002004C
►유형 : 캐릭터
►구조 : COG+PCB
►20 문자 x 4 라인
►IC:SSD1311
►3.3V/5V 전원 공급 장치
►1/32 duty
►인터페이스 : 6800,8080,SPI,I2C
►디스플레이 색상: 백색 / 노란색
WEA002004C, PCB board ile entegre edilmiş bir COG karakter OLED ekran modülüdür; çapraz boyutu 2.89 inç olup, 20 karakter x 4 satırdan oluşur ve yüksek 10.000:1 kontrast oranı sayesinde çok okunaklıdır. Modül, SSD1311 IC ile donatılmıştır ve 6800/8080 4-bit/8-bit paralel, 4-Damla SPI ve I2C arayüzlerini destekler, 1/32 görev döngüsü ile çalışır. Mantık için besleme gerilimi 5V olup, opsiyonel olarak 3.3V seçeneği mevcuttur. Bu model, ASCII, İngilizce, Avrupa ve Japonca karakterler için yerleşik ROM'lara sahiptir.
WEA002004C, PCB board üzerinde montaj delikleri bulunan bir COG karakter OLED ekran modülüdür; bu, modülü müşterilerin uygulamalarında kolayca monte etmeyi sağlar.
WEA002004C OLED modülü, akıllı ev uygulamaları, medikal cihazlar, akıllı kontrol sistemleri, sayaçlar ve daha fazlası için uygundur. Bu modül, -40℃ ile +80℃ arasındaki sıcaklıklarda çalışabilir ve -40℃ ile +85℃ arasındaki sıcaklıklarda saklanabilir.
Data source ref: WEA002004CWPP3N00000
Pin No. | 기호 | Pin Type | 기능 | ||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | P | Ground | ||||||||||||||||||
2 | VDD | P | Power supply and power supply for interface logic level. | ||||||||||||||||||
3 | REGVDD | I | This pin is pulled LOW, internal VDD regulator is disabled (Low voltage I/O application). | ||||||||||||||||||
4 | D/C# | I | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When serial interface is selected, this pin must be connected to VSS. |
||||||||||||||||||
5 | R/W# (WR#) | I | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||||||||||
6 | E/RD# | I | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||||||||||
7 | D0 | I/O | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID and D2 will be the serial data output: SOD. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||||||||||
8 | D1 | ||||||||||||||||||||
9 | D2 | ||||||||||||||||||||
10 | D3 | ||||||||||||||||||||
11 | D4 | ||||||||||||||||||||
12 | D5 | ||||||||||||||||||||
13 | D6 | ||||||||||||||||||||
14 | D7 | ||||||||||||||||||||
15 | CS# | I | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). In I2C mode, this pin must be connected to VSS. |
||||||||||||||||||
16 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||||||||||
17 | BS0 | I | setting as described in the following table. BS2, BS1 and BS0 are pin select. Bus Interface selection
(1) 0 is connected to VSS (2) 1 is connected to VDD |
||||||||||||||||||
18 | BS1 | ||||||||||||||||||||
19 | BS2 | ||||||||||||||||||||
20 | VSS (FRGnd) |
P | Ground |
항목 | 치수 | 단위 |
---|---|---|
디스플레이 형식 | 20 문자 x 4 라인 | - |
모듈 치수 | 92.0 x 31.5 x 5.96 Max. | mm |
보기 영역 | 72.42 x 22.82 | mm |
활성 영역 | 70.42 x 20.82 | mm |
도트 크기 | 0.57 x 0.57 | mm |
도트 피치 | 0.60 x 0.60 | mm |
캐릭터 크기 | 2.97 x 4.77 | mm |
캐릭터 피치 | 3.55 x 5.35 | mm |
LCD 유형 | OLED , Monochrome | |
Duty | 1/32 | |
IC | SSD1311 | |
인터페이스 | 6800, 8080, SPI, I2C | |
크기 (대각선) | 2.89 인치 |
항목 | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
작동 온도 | TOP | -40 | +80 | °C |
보관 온도 | TST | -40 | +85 | °C |
Supply Voltage For Logic | VDD-VSS | -0.3 | 3.6 | V |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage For Logic | VDD-VSS | - | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | - | 0.8xVDD | - | VDD | V |
Input Low Volt. | VIL | - | GND | - | 0.2xVDD | V |
Output High Volt. | VOH | IOH=-0.5mA | 0.8xVDD | - | VDD | V |
Output Low Volt. | VOL | IOL=0.5mA | GND | - | 0.2xVDD | V |
Display 50% Pixel on | IDD | VDD=3V | - | 110 | 220 | mA |
Search keyword: oled 20x4, 20x4 oled
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책