私たちはあなたのプライバシーを大切にします
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー
WEO012864AM は、2.7 インチ COG 128x64 グラフィック OLED ディスプレイです。 このモジュールには SH1106 IC が内蔵されて、 I2C、4 線 SPI シリアル、または 6800、8080 パラレル インターフェイスを介して通信できて、10,000:1 の高コントラスト比により表示画像がより鮮明になります。 ロジック電源電圧は1.65V~3.3V(代表値3V)、表示用電源電圧は6.4V~13.5V(代表値13V)、駆動デューティは1/64です。
このモジュールは-40℃~+80℃の温度で動作できて、保管温度範囲は-40℃~+85℃です。 2.7インチOLEDは、スマートホームアプリケーション、ハイテク機器、メーター機器、産業用制御システム、医療機器、IoTシステムなどに非常に適しております。 WEO12864AM シリーズには異なる ZIF FPC があります。 現在、オプションとして 22 ピン、24 ピン、30 ピン、及び 31 ピンを提供しています。 FPC がカスタムとして評価する必要な場合は、お気軽にお問い合わせください。
項目 | 仕様 | 単位 |
---|---|---|
ドットマトリックス(解像度) | 128 × 64 | - |
モジュールサイズ | 73.0 × 41.86 × 2.01 | mm |
有効エリア | 61.41 × 30.69 | mm |
ドットサイズ | 0.45 × 0.45 | mm |
ドットピッチ | 0.48 × 0.48 | mm |
表示モード | パッシブマトリックス | |
発光色 | モノクロ | |
駆動方法 | 1/64 Duty | |
IC | SH1106 | |
インターフェイス | 6800,8080,4-Wire SPI,I2C | |
表示サイズ(対角線) | 2.7 インチ |
パラメーター | 記号 | 最小値 | 最大値 | 単位 |
---|---|---|---|---|
ロジック電源電圧 | VDD1 | -0.3 | 3.6 | V |
Display電源電圧 | VPP | -0.3 | 14.5 | V |
操作温度 | TOP | -40 | +80 | °C |
保存温度 | TSTG | -40 | +85 | °C |
項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
---|---|---|---|---|---|---|
ロジック電源電圧 | VDD1 | - | 1.65 | 3.0 | 3.3 | V |
Display電源電圧 | VPP | - | 6.4 | 13.0 | 13.5 | V |
高レベル入力 | VIH | - | 0.8×VDD1 | - | VDD1 | V |
低レベル入力 | VIL | - | VSS | - | 0.2×VDD1 | V |
高レベル出力 | VOH | - | 0.8×VDD1 | - | VDD1 | V |
低レベル出力 | VOL | - | VSS | - | 0.2×VDD1 | V |
Display 50% Pixel on | IPP | VPP =13V | - | 24 | 36 | mA |
No. | 記号 | 説明 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | ESD_GND | ESD Ground pin | |||||||||||||||
2 | VSS | Ground. | |||||||||||||||
3-10 | NC | No connection | |||||||||||||||
11 | VDD1 | Power supply input | |||||||||||||||
12 | IM1 | These are the MPU interface mode select pads.
(1) 0 is connected to VSS (2) 1 is connected to VDD1 |
|||||||||||||||
13 | IM2 | ||||||||||||||||
14 | NC | No connection | |||||||||||||||
15 | /CS | This pad is the chip select input. When /CD = “L”, then the chip select becomes active, and data/command I/O is enabled. | |||||||||||||||
16 | /RES | This is a reset signal input pad. When /RES is set to “L”, the settings are initialized. The reset operation is performed by the /RES signal level. | |||||||||||||||
17 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
|||||||||||||||
18 | /WR (R/W) |
This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W= “H”: Read. When R/W= “L”: Write. |
|||||||||||||||
19 | E/RD | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the /RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU. When /RD = “H”: Enable. When /RD = “L”: Disable. |
|||||||||||||||
20~27 | D0~D7 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance. |
|||||||||||||||
28 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA. | |||||||||||||||
29 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
30 | VPP | OLED panel power supply. It could be supplied externally. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
31 | ESD_GND | ESD Ground pin |
「すべてのクッキーを許可」をクリックすると、サイトのナビゲーションを向上させ、サイト使用状況を分析し、マーケティングおよびパフォーマンスの取り組みを支援するために、クッキーをデバイスに保存することに同意したことになります。この件に関する詳細情報は、ポリシーをご覧ください。プライバシーポリシー