제품 OLED 디스플레이 그래픽 OLED 디스플레이 WEO012864AM

128x64 그래픽 2.7 인치 COG OLED 디스플레이 모듈

모델 번호 WEO012864AM

►유형 : 그래픽
►구조 : COG
►크기 : 2.7 인치
►128 x 64 점 행렬
►IC:SH1106
►3V 전원 공급 장치
►1/64 duty
►인터페이스 : 6800,8080,4-wire SPI,I2C
►디스플레이 색상: 백색 / 노란색

설명

WEO012864AM, 이 제품은 COG OLED 디스플레이로 128 x 64도트로 구성되어 있으며 , 개별 단색으로 구성되었습니다, 대각선 길이는 2.7인치입니다. 이 모듈의 모듈 크기는 73.0×41.86 mm이며 활성 영역 면적은 561.41×30.69 mm입니다, 대비(일반값) 는 10,000:1입니다.

WEO012864AM, 이 OLED 모듈에는 SH1106 컨트롤러나 그와 동급의 IC가 기본 내장되어 있습니다. 이 제품은 6800, 8080, 4와이어 SPI 및 I2C 인터페이스. 이 2.7인치 OLED 모듈 시리즈의 작동 온도는 -40℃에서 +80℃이며, 보관 온도 범위는 -40℃에서 +85℃입니다. 논리 공급 전압의 경우 1.65V에서 3.3V, 일반값 3.0V, 구동 부하 1/64입니다.

유기 발광 다이오드(Organic Light-Emitting Diode, OLED)는 차세대 기술로, 더 밝고 선명한 이미지에 더욱 빠른 응답 속도를 제공합니다. 이 모듈은 초박형의 소형 경량 COG OLED 디스플레이로, 전력 소모량도 적습니다. 의료 기기, 휴대용 디바이스, 측량기, 공업용 컨트롤 시스템, 의료 기기 등에 이상적입니다.

WEO012864AH, WEO012864AL, WEO012864AM

도면

128x64 Graphic 2.7-inch COG OLED Display Module - WEO012864AM

Data source ref:WEO012864AMWPP3N00000

사양

기계적 데이터

항목 치수 단위
도트 매트릭스 128 × 64 dots
모듈 치수 73.0 × 41.86 × 2.01 mm
활성 영역 61.41 × 30.69 mm
도트 크기 0.45 × 0.45 mm
도트 피치 0.48 × 0.48 mm
디스플레이 모드 패시브 매트릭스 (Passive Matrix)
디스플레이 색 Monochrome
Drive Duty 1/64 Duty
IC SH1106
인터페이스 6800,8080,4-Wire SPI,I2C
크기 2.7 인치

절대 최대 정격값

Parameter 기호 최소값 최대값 단위
Supply Voltage for Logic VDD1 -0.3 3.6 V
Supply Voltage for Display VPP -0.3 14.5 V
작동 온도 TOP -40 +80 °C
보관 온도 TSTG -40 +85 °C

전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for Logic VDD1 1.65 3.0 3.3 V
Supply Voltage for Display VPP 6.4 13.0 13.5 V
High Level Input VIH 0.8×VDD1 VDD1 V
Low Level Input VIL VSS 0.2×VDD1 V
High Level Output VOH 0.8×VDD1 VDD1 V
Low Level Output VOL VSS 0.2×VDD1 V
Display 50% Pixel on IPP VPP =13V 24 36 mA

인터페이스 핀 기능

No. 기호 기능
1 ESD_GND ESD Ground pin
2 VSS Ground.
3-10 NC No connection
11 VDD1 Power supply input
12 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
13 IM2
14 NC No connection
15 /CS This pad is the chip select input. When /CD = “L”, then the chip select becomes active, and data/command I/O is enabled.
16 /RES This is a reset signal input pad. When /RES is set to “L”, the settings are initialized. The reset operation is performed by the /RES signal level.
17 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
18 /WR
(R/W)
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W= “H”: Read.
When R/W= “L”: Write.
19 E/RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the /RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When /RD = “H”: Enable.
When /RD = “L”: Disable.
20~27 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
28 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
29 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
30 VPP OLED panel power supply. It could be supplied externally.
A capacitor should be connected between this pad and VSS.
31 ESD_GND ESD Ground pin
go top
close

우리는 귀하의 프라이버시를 소중히 여깁니다

"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책

우리는 귀하의 프라이버시를 소중히 여깁니다

Winstar와 일부 제3자는 www.winstar.com.tw에서 쿠키를 사용합니다. 쿠키의 종류, 목적 및 관련된 제3자에 대한 자세한 내용은 아래 및 당사의 쿠키 정책에 설명되어 있습니다. 웹사이트에서 최상의 경험을 얻으려면 "모두 허용"을 클릭하여 당사의 쿠키 사용에 동의해 주세요. 또한 선호 설정을 하거나 필수 쿠키를 제외한 쿠키를 거부할 수도 있습니다.

동의 설정 관리

항상 활성화
필수 쿠키

이 쿠키는 웹사이트를 탐색하고 개인 정보 설정, 로그인 또는 양식 작성과 같은 기능을 사용할 수 있도록 하는 데 필수적입니다.

분석 쿠키

“통계 쿠키”라고도 알려진 이러한 쿠키는 웹사이트 사용에 대한 정보를 수집합니다. 예를 들어 어떤 페이지를 방문했는지, 어떤 링크를 클릭했는지와 같은 정보입니다. 자세한 내용을 확인하세요.