製品情報
このCOG 有機EL 128x64は最も一般的に使用されます。Winstar Displayが発表した市場に人気がある標準な有機EL COGグラフィック機種はWEO012864GとWEO012864Hです。この二つモデルは、同じの有機ELパネルが有りますが、異なるFPCピン配列されております。WEO012864G にZIF FPCを使用し、WEO012864H にホットバーFPCを使用します。客様は製品アプリケーションにより、相応しいOLED 128ｘ64モジュールを選択できます。SSD1309 ICが内蔵され、6800/8080/SPI/I2Cのインターフェースをサポート致します。有機EL･COGモジュールは超薄、軽量、低消費電力のメリットを有して、ハンドヘルド機器、メーター、スマートグリッド、ウェアラブル機器、IoTシステムなどに生かせます。
Frame Option | FPC Options 外形図
Data source ref: WEO012864GWPP3N00000
製品仕様
ピン功能定義
| No. | 記号 | 説明 | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(GND) | No connection | |||||||||||||||
| 2 | VSS | Ground. | |||||||||||||||
| 3-10 | NC | No connection | |||||||||||||||
| 11 | VDD | Power supply pin for core logic operation | |||||||||||||||
| 12 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
| 13 | BS2 | ||||||||||||||||
| 14 | NC | No connection | |||||||||||||||
| 15 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
| 16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
| 17 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
| 18 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 19 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
| 20~27 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
| 28 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
| 29 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
| 30 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
| 31 | NC(GND) | No connection |
規格説明
| 項目 | 仕様 | 単位 |
|---|---|---|
| ドットマトリックス | 128 x 64 | － |
| モジュールサイズ | 60.5 × 37.0 × 2.11 | mm |
| アクティブエリア | 55.01 × 27.49 | mm |
| ピクセルサイズ | 0.40 × 0.40 | mm |
| ピクセルピッチ | 0.43 × 0.43 | mm |
| 表示モード | パッシブマトリクス | |
| 発光色 | モノクロ | |
| 駆動方法 | 1/64 Duty | |
| IC | SSD1309 | |
| インターフェイス | 6800,8080,4-Wire SPI,I2C | |
| サイズ | 2.42 インチ | |
絶対最大定格
| パラメーター | 記号 | 最小値 | 最大値 | 単位 |
|---|---|---|---|---|
| ロジック電源電圧 | VDD | -0.3 | 4 | V |
| 表示用電源電圧 | VCC | 0 | 15 | V |
| 操作温度 | TOP | -40 | +80 | °C |
| 保存温度 | TSTG | -40 | +85 | °C |
電気特性
| 項目 | 記号 | 条件 | 最小値 | 典型値 | 最大値 | 単位 |
|---|---|---|---|---|---|---|
| ロジック電源電圧 | VDD | － | 1.65 | 3.0 | 3.3 | V |
| 表示用電源電圧 | VCC | － | 7.0 | 13.0 | 13.5 | V |
| 高レベル入力 | VIH | － | 0.8×VDD | － | － | V |
| 低レベル入力 | VIL | － | － | － | 0.2×VDD | V |
| 高レベル出力 | VOH | － | 0.9×VDD | － | － | V |
| 低レベル出力 | VOL | － | － | － | 0.1×VDD | V |
| Display 50% Pixel on | ICC | VCC =13V | － | 18 | 27 | mA |
Frame Option:
| Drawing | Material | FR No. | Detailed Drawing | Create Date |
|---|---|---|---|---|
 |
SUS-304 | FFL6D00049AA121XXX00 | View | 20160429 |
FPC Options:
| Drawing | FPC Length | PIN | pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
37 | 31 | 0.5 | ZIF | 6800,8080,SPI,I2C | FPC2050003111XXXXX01 | 20130625 |
 |
19.75 | 31 | 1 | HOTBAR | 6800,8080,SPI,I2C | FPC2100003101XXXXX02 | 20140220 |
 |
37.15 | 24 | 0.5 | ZIF | 6800,8080,SPI,I2C | FPC2000502411XXXXX01 | 20160803 |
 |
70.85 | 22 | 0.5 | ZIF | 6800,8080,SPI,I2C | FPC2050002211XXXXX03 | 20161228 |
 |
106.57 | 30 | 0.5 | ZIF | 6800,8080,SPI,I2C | FPC2050003011XXXXX11 | 20180620 |
Search keyword: 128x64 oled, oled 128x64, 2.42 oled, 2.42" oled, 2.42インチoled, oled 2.42, oled 2.42"
