Startseite Produkte OLED-Anzeige Grafik-OLED-Anzeigen WEO012864G
2,42 Grafik-OLED-Module 128x64 - WEO012864G
2,42 Grafik-OLED-Module 128x64 - WEO012864G
2,42 Grafik-OLED-Module 128x64 - WEO012864G
2,42 Grafik-OLED-Module 128x64 - WEO012864G
2,42 Grafik-OLED-Module 128x64 - WEO012864G

2,42" Grafik-OLED-Module 128x64

Modellnummer WEO012864G

►Typ: Grafik
►Bauweise: COG; Frame Option
►Größe: 2,42 Zoll OLED
►128 x 64 Punktmatrix
►IC：SSD1309
►3-V-Stromversorgung
►1/64 duty
►Schnittstelle: 6800, 8080, SPI, I2C
►die Farbe des Displays: Weiß / Gelb / Himmelblau / Grün
►Andere in der nachstehenden Tabelle verfügbare FPC-Optionen

Zurück Zurück zur Liste Weiter

Beschreibung

Die Winstar 2,42" OLED WEO012864G und WEO012864H beide haben die COG-Stuktur und die Auflösung von 128x64 Pixeln. Diese Modelle sind mit dem gleichen OLED-Panel bestückt, haben aber unterschiedliche FPC. Das WEO012864G enthält das ZIF-FPC und das WEO012864H ein Hot-Bar-FPC. Das WEO012864G ist mit dem Controller SSD1309 ausgestattet und unterstützt die Schnittstellen 6800, 8080, SPI und I2C. Diese COG OLED-Module sind sehr dünn, leicht und verbrauchen nur wenig Energie. Sie eignen sich hervorragend für Handgeräte, Messgeräte, Smart-Grid, IoT usw.

     Rahmenoption | FPC-Optionen

Zeichnung

2.42 inch OLED Display, 2.42 OLED 128x64 - WEO012864G

Data source ref: WEO012864GWPP3N00000

Technische Daten

Schnittstelle Pin-Funktion

No. Symbol Beschreibung
1 NC(GND) No connection
2 VSS Ground.
3-10 NC No connection
11 VDD Power supply pin for core logic operation
12 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX Parallel 0 1
8-bit 80XX Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
13 BS2
14 NC No connection
15 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
18 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
19 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
20~27 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
28 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
29 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
30 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
31 NC(GND) No connection

mechanische Daten

Artikel Ausmaß Einheit
Punktmatrix 128 x 64 －
Abmaße der modul 60,5 × 37,0 × 2,11 mm
Aktiver Bereich 55,01 × 27,49 mm
Pixelgröße 0,40 × 0,40 mm
Pixelabstand 0,43 × 0,43 mm
der Anzeigemodus Passive Matrix
die Farbe des Displays Monochrome
Drive Duty 1/64 Duty
IC SSD1309
Schnittstelle 6800,8080,4-Wire SPI,I2C
Größe 2,42 Zoll

Absolute Grenzwerte

Parameter Symbol Mindestwert Maximalwert Einheit
Supply Voltage for Logic VDD -0,3 4 V
Supply Voltage for Display VCC 0 15 V
Betriebstemperatur TOP -40 +80 °C
Lagertemperatur TSTG -40 +85 °C

elektronische Eingenschaften

Artikel Symbol Bedingung Mindestwert typischer Wert Maximalwert Einheit
Supply Voltage for Logic VDD － 1,65 3,0 3,3 V
Supply Voltage for Display VCC － 7,0 13,0 13,5 V
High Level Input VIH － 0,8×VDD － － V
Low Level Input VIL － － － 0,2×VDD V
High Level Output VOH － 0,9×VDD － － V
Low Level Output VOL － － － 0,1×VDD V
Display 50% Pixel on ICC VCC =13V － 18 27 mA

Rahmenoption:

Bild Material FR No. Detailed Drawing Create Date
WEF012864G SUS-304 FFL6D00049AA121XXX00 View 20160429

FPC-Optionen:

Bild FPC Length PIN pitch ZIF FPC or HOTBAR FPC Schnittstelle FPC No. Create Date
FPC2050003111XXXXX01_WEO012864KLPP3N00000 37 31 0.5 ZIF 6800,8080,SPI,I2C FPC2050003111XXXXX01 20130625
FPC2100003101XXXXX02_WEO012864HWPP3N00000 19.75 31 1 HOTBAR 6800,8080,SPI,I2C FPC2100003101XXXXX02 20140220
FPC2000502411XXXXX01_WEO012864GSAP3N00F00 37.15 24 0.5 ZIF 6800,8080,SPI,I2C FPC2000502411XXXXX01 20160803
FPC2050002211XXXXX03_WEO012864KWPP3N00F00 70.85 22 0.5 ZIF 6800,8080,SPI,I2C FPC2050002211XXXXX03 20161228
FPC2050003011XXXXX11_WEF012864HLPP3N00F00 106.57 30 0.5 ZIF 6800,8080,SPI,I2C FPC2050003011XXXXX11 20180620
go top
close