N° de modèle WEO020636A
►Type: Graphique
►Structure: COG
►Dimension: 1.92 pouces
►Matrice de points 160 x 128
►IC：SSD1362
►Alimentation 3V
►1/36 duty
►Interface: SPI,I2C
►Couleur d'affichage: Blanc
►Support d’échelle grise
Découvrez la série WEO020636A, le premier module OLED de 2,55 pouces de Winstar avec une résolution de 206x36 pixels. Cet affichage OLED graphique COG (Chip on Glass) présente des dimensions extérieures de 70,77 x 15,14 mm et une zone active de 63,84 x 11,14 mm, offrant une représentation visuelle précise.
L'affichage OLED WEO020636A est idéal pour des applications telles que les amplificateurs de casque DAC portables, les stations d'alimentation portables et les applications radio. Sa taille compacte et sa clarté visuelle exceptionnelle le rendent adapté aux appareils mobiles, équipements industriels, dispositifs médicaux et électronique grand public. La structure COG de l'affichage et sa compatibilité avec les interfaces SPI et I2C facilitent une intégration transparente dans différents environnements numériques.
Que ce soit pour améliorer les interfaces utilisateur des appareils portables ou fournir un retour visuel critique dans des environnements industriels, le WEO020636A garantit des performances fiables et une durabilité sur une large plage de température.
| No. | Symbole | Fonction | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||
| 2 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||
| 3 | VP | This pin is the segment pre-charge voltage reference pin. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||
| 4 | VSL | This is a reserved pin. It should be connected to VLSS externally. | ||||||||
| 5 | VLSS | Analog system ground pin. It must be connected to external ground. | ||||||||
| 6 | VDD | VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.A capacitor should be connected between VDD and VSS under all circumstances. | ||||||||
| 7 | VCI | Low voltage power supply. VCI must always be equal to or higher than VDD and VDDIO. |
||||||||
| 8 | VDDIO | Power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. | ||||||||
| 9 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled Low (active Low).In I2C mode, this pin must be connected to VSS. |
||||||||
| 10 | RES# | This pin is reset signal input. When the pin is pulled Low, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||
| 11 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data will be interpreted as data. When the pin is pulled LOW, the data will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||
| 12 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie Low. When serial interface mode is selected,D0 will be the serial clock input: SCLK;D1 will be the serial data input: SID. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||
| 13 | D1 | |||||||||
| 14 | D2 | |||||||||
| 15 | BS0 | MCU bus interface selection pins.
|
||||||||
| 16 | BS1 | |||||||||
17 |
VSS | Ground pin. | ||||||||
| 18 | IREF | When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA. When internal IREF is used, this pin should be kept NC. |
||||||||
| 19~20 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. |
| Article | Dimensions | Unité |
|---|---|---|
| Matrice de points | 206 x 36 points | － |
| Dimensions du module | 70.77 x 15.14 x 2.01 | mm |
| Zone active | 63.84 x 11.14 | mm |
| Taille des points | 0.29 x 0.29 | mm |
| Pas des points | 0.31 x 0.31 | mm |
| Mode d'affichage | Matrice passive | |
| Couleur d'affichage | Monochrome | |
| Drive Duty | 1/36 Duty | |
| Scala di grigi | 4 Bits | |
| IC | SSD1362 | |
| Interface | 3-Wire SPI、4-Wire SPI、I2C | |
| Diagonale | 2.55 pouces | |
| Article | Symbole | Valeur min | Valeur max | Unité |
|---|---|---|---|---|
| Supply Voltage | VDD | -0.5 | 2.75 | V |
| Supply Voltage | VCI | -0.3 | 5.5 | V |
| Supply Voltage | VDDIO | -0.5 | 5.5 | V |
| Supply Voltage | VCC | 7 | 21 | V |
| Température de fonctionnement | TOP | -40 | +80 | °C |
| Température de stockage | TSTG | -40 | +85 | °C |
| Article | Symbole | État | Min | Typ | Max | Unité |
|---|---|---|---|---|---|---|
| Supply Voltage for Display | VCC | － | 10.0 | 12.0 | 12.5 | V |
| Low voltage power supply | VCI | － | 1.65 | － | 3.5 | V |
| Power supply for I/O pins | VDDIO | － | 1.65 | － | VCI | V |
| Logic Supply Voltage | VDD | － | 1.65 | － | 2.6 | V |
| High Level Input | VIH | － | 0.8×VDDIO | － | － | V |
| Low Level Input | VIL | － | － | － | 0.2×VDDIO | V |
| High Level Output | VOH | － | 0.9×VDDIO | － | － | V |
| Low Level Output | VOL | － | － | － | 0.1×VDDIO | V |
| Display 50% Pixel on | ICC | VCC =12V | － | 25 | 35 | mA |
Search keyword: 206x36 oled, oled 206x36, 2.55" oled, 2.55 pouces oled, oled 2.55"
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.