首頁 產品介紹 OLED顯示器 繪圖型 OLED 顯示器 WEO012864AE

1.54吋OLED, 128x64 SPI OLED模組

型號 WEO012864AE

►類型: 繪圖型
►結構: COG
►尺寸:1.54吋
►128 x 64 點陣
►IC:CH1116
►3V電源電壓
►1/64 duty
►介面: 6800,8080,4-wire SPI,I2C
►發光顏色: 白色 / 黃色
►MOQ:150K, 您可以選擇 WEO012864AH 作為 WEO0112864AE 的替代。

產品敘述

WEO012864AE是一款1.54吋COG 128x64繪圖型OLED顯示器。此COG模組內建CH1116控制器IC可支援I2C、4線SPI、6800和8080並列介面;電源電壓典型值為 3V,顯示器電源電壓典型值為12.5V,驅動方式為1/64 duty。WEO12864AE系列有不同的ZIF FPC:我們提供24 pins和30 pins可選。如果您需要客製化FPC,歡迎隨時聯絡我們。

WEO012864AE非常適合物聯網系統、智能家電、POS系統、智能設備、能源系統、通信系統和醫療產品等。此模組工作溫度為-40℃至+ 80℃,儲存溫度為-40℃至+85℃。

 

規格圖

1.54 inch OLED, 128x64 SPI OLED Display - WEO012864AE
Data source ref:WEO012864AEWAP3N00000

產品規格

Pin功能定義

No. 符號 功能說明
1 NC(GND) No connection
2 VSS Ground.
3 VSS Ground.
4 NC No connection
5 VDD1 Power supply input
6 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
7 IM2
8 CS# This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 RES# This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR#
(R/W#)
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W#= “H”: Read.
When R/W#= “L”: Write.
12 E/RD# This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD# = “H”: Enable.
When RD# = “L”: Disable.
13-20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection

規格說明

項目 規格說明 單位
點陣(解析度) 128 × 64
模組尺寸 42.04 × 27.22 × 1.41 mm
有效區域 35.05 × 17.51 mm
像素大小 0.249 × 0.249 mm
像素間距 0.274 × 0.274 mm
顯示模式 Passive Matrix 被動矩陣
顯示顏色 單色
驅動方式 1/64 Duty
IC CH1116
介面 6800,8080,4-wire SPI,I2C
尺寸 1.54 吋

最大絕對額定值

參數 符號 最小值 最大值 單位
邏輯電源電壓 VDD -0.3 3.6 V
顯示電源電壓 VCC 0 14.5 V
工作溫度 TOP -40 +80 °C
儲存溫度 TSTG -40 +85 °C

電氣特性

項目 符號 條件 最小值 典型值 最大值 單位
邏輯電源電壓 VDD1 1.65 3.0 3.3 V
顯示電源電壓 VPP 6.4 12.5 13.0 V
輸入高準位 VIH 0.8×VDD1 VDD1 V
輸入低準位 VIL VSS 0.2×VDD1 V
輸出高準位 VOH 0.8×VDD1 VDD1 V
書出低準位 VOL VSS 0.2×VDD1 V
Display 50% Pixel on IPP VPP =12.5V 8 12 mA
 

Search keyword: 128x64 oled, oled 128x64, 1.54 oled, 1.54" oled, 1.54 inch oled, oled 1.54, oled 1.54", 1.54吋oled, oled 1.54吋

go top
close

我們重視您的隱私

通過點擊「允許所有 Cookie」,代表您同意在您的設備上存儲 Cookie 以增強網站瀏覽體驗、分析網站使用情況並協助我們的行銷和網站效能優化工作。您可以在我們的隱私權政策中找到有關於此的更多資訊。

我們重視您的隱私

Winstar 及部分第三方在 www.winstar.com.tw 上使用 cookies。關於 cookie 的種類、用途及相關第三方的詳細資訊,請參見下文及我們的《Cookie 政策》。請點擊「允許全部」來同意我們使用 cookies,以確保您在我們網站上獲得最佳體驗。您也可以設置您的偏好或拒絕 cookies(必要的 cookies 除外)。

管理同意聲明

永久啟用
必要的 Cookie

這些 Cookie 是必不可少的,以便讓您在瀏覽網站並使用其功能上有更好地體驗,例如設置您的隱私偏好、登錄或填寫表單。

分析 Cookie

這些也被稱為「統計cookie」,用於收集您使用網站的資訊,例如您訪問了哪些頁面以及點擊了哪些連結。查看詳細資訊