N° de modèle WEO012864AE
►Type: Graphique
►Structure: COG
►Dimension: 1.54 pouces
►Matrice de points 128 x 64
►IC：CH1116
►Alimentation 3V
►1/64 duty
►Interface: 6800,8080,4-wire SPI,I2C
►Couleur d'affichage: Blanc / Jaune
►MOQ：150K. Vous pouvez choisir WEO012864AH en remplacement de WEO012864AE.
Le modèle WEO012864AE est un écran OLED graphique COG de 1,54 pouce avec une résolution de 128x64 pixels. Ce module est intégré au circuit intégré CH1116 ; il peut être communiqué via l'interface I2C, SPI à 4 lignes, 6800 ou 8080 en parallèle ; la tension d'alimentation pour la logique est de 3V (valeur typique), la tension d'alimentation pour l'affichage est de 12,5V (valeur typique), avec un cycle de fonctionnement de 1/64. La série WEO12864AE dispose de différents FPC ZIF ; actuellement, nous proposons en option des FPC de 24 et 30 broches si les clients nécessitent un FPC personnalisé, n'hésitez pas à nous contacter.
Le modèle WEO012864AE est idéal pour les systèmes IoT, les applications domotiques, les terminaux de paiement financiers, les appareils technologiques intelligents, les systèmes énergétiques, les systèmes de communication, les instruments médicaux, etc. Ce module peut fonctionner à des températures de -40℃ à +80℃ ; ses températures de stockage vont de -40℃ à +85℃.
| No. | Symbole | Function | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC(GND) | No connection | |||||||||||||||
| 2 | VSS | Ground. | |||||||||||||||
| 3 | VSS | Ground. | |||||||||||||||
| 4 | NC | No connection | |||||||||||||||
| 5 | VDD1 | Power supply input | |||||||||||||||
| 6 | IM1 | These are the MPU interface mode select pads.
(1) 0 is connected to VSS (2) 1 is connected to VDD1 |
|||||||||||||||
| 7 | IM2 | ||||||||||||||||
| 8 | CS# | This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled. | |||||||||||||||
| 9 | RES# | This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level. | |||||||||||||||
| 10 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
|||||||||||||||
| 11 | WR# (R/W#) |
This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W#= “H”: Read. When R/W#= “L”: Write. |
|||||||||||||||
| 12 | E/RD# | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU. When RD# = “H”: Enable. When RD# = “L”: Disable. |
|||||||||||||||
| 13-20 | D0~D7 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance. |
|||||||||||||||
| 21 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA. | |||||||||||||||
| 22 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
| 23 | VPP | OLED panel power supply. Generated by internal charge pump. Connect to capacitor. It could be supplied externally. |
|||||||||||||||
| 24 | NC(GND) | No connection |
| Article | Dimensions | Unité |
|---|---|---|
| Matrice de points | 128 × 64 | dots |
| Dimensions du module | 42.04 × 27.22 × 1.41 | mm |
| Zone active | 35.05 × 17.51 | mm |
| Pixel Size | 0.249 × 0.249 | mm |
| Pixel Pitch | 0.274 × 0.274 | mm |
| Mode d'affichage | Matrice passive | |
| Couleur d'affichage | Monochrome | |
| Drive Duty | 1/64 Duty | |
| IC | CH1116 | |
| Interface | 6800,8080,4-wire SPI,I2C | |
| Diagonale | 1.54 pouces | |
| Parameter | Symbole | Min | Max | Unité |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
| Supply Voltage for Display | VCC | 0 | 14.5 | V |
| Température de fonctionnement | TOP | -40 | +80 | °C |
| Température de stockage | TSTG | -40 | +85 | °C |
| Article | Symbole | État | Min | Typ | Max | Unité |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD1 | － | 1.65 | 3.0 | 3.3 | V |
| Supply Voltage for Display | VPP | － | 6.4 | 12.5 | 13.0 | V |
| High Level Input | VIH | － | 0.8×VDD1 | － | VDD1 | V |
| Low Level Input | VIL | － | VSS | － | 0.2×VDD1 | V |
| High Level Output | VOH | － | 0.8×VDD1 | － | VDD1 | V |
| Low Level Output | VOL | － | VSS | － | 0.2×VDD1 | V |
| Display 50% Pixel on | IPP | VPP =12.5V | － | 8 | 12 | mA |
Search keyword: 128x64 oled, oled 128x64, 1.54 oled, 1.54" oled, 1.54 inch oled, oled 1.54, oled 1.54"
En cliquant sur "Autoriser tous les cookies", vous acceptez le stockage de cookies sur votre appareil pour améliorer la navigation sur le site, analyser l'utilisation du site et aider dans nos efforts de marketing et de performance. Vous pouvez trouver plus d'informations à ce sujet dans notre politique. Politique de confidentialité