我们重视您的隐私
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
WEF012864G是一款2.42寸绘图型COG单色被动式PMOLED显示模块加铁框,面板分辨率为128x64像素具高对比度(10,000:1)。 WEF012864G内置SSD1309控制器IC,支持多种传输接口,包括6800、8080、4-Wire SPI和I2C接口。 它使用占空比为 1/64 的 3V 电压驱动。 该系列采用与现有WEO012864G相同尺寸的OLED面板:
WEO012864G 系列采用铁质无框设计。
WEO012864G-CTP 系列采用铁质无框+电容触摸屏(CTP)。
WEF012864G是一款COG结构的OLED显示模块。 它是有机的、自发光的并且不需要背光。 该模块薄、轻、功耗低。 WEF012864G模块非常适合手持产品、测量仪器和家用产品,可用于物联网、通信设备和医疗仪器。 该模块工作温度为-40℃至+80℃,存储温度为-40℃至+85℃。
项目 | 规格 | 单位 |
---|---|---|
点阵(分辨率) | 128 x 64 | dots |
模块尺寸 | 77.2 × 42.14 × 3.4 | mm |
有效区域 | 55.01 × 27.49 | mm |
像素大小 | 0.40 × 0.40 | mm |
像素间距 | 0.43 × 0.43 | mm |
顯示模式 | 被动矩阵 | |
发光颜色 | 单色 | |
驱动方式 | 1/64 Duty | |
IC | SSD1309 | |
接口 | 6800,8080,4-Wire SPI,I2C | |
尺寸(对角线) | 2.42 寸 |
参数 | 符号 | 最小值 | 最大值 | 单位 |
---|---|---|---|---|
逻辑电源电压 | VDD | -0.3 | 4.0 | V |
显示电源电压 | VCC | 0 | 15.0 | V |
工作温度 | TOP | -40 | +80 | °C |
储存温度 | TSTG | -40 | +85 | °C |
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
逻辑电源电压 | VDD | - | 1.65 | 3.0 | 3.3 | V |
显示电源电压 | VCC | - | 12.5 | 13 | 13.5 | V |
输入高准位 | VIH | - | 0.8×VDD | - | - | V |
输入低准位 | VIL | - | - | - | 0.2×VDD | V |
输出高准位 | VOH | - | 0.9×VDD | - | - | V |
输出低准位 | VOL | - | - | - | 0.1×VDD | V |
50%显示画面耗电流 | VCC =13.0V | - | 18 | 27 | mA |
Pin No. | 符号 | 功能说明 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | NC(GND) | No connection | |||||||||||||||
2 | VSS | Ground. | |||||||||||||||
3-10 | NC | No connection | |||||||||||||||
11 | VDD | Power supply pin for core logic operation | |||||||||||||||
12 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
13 | BS2 | ||||||||||||||||
14 | NC | No connection | |||||||||||||||
15 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). | |||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. | |||||||||||||||
17 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. | |||||||||||||||
18 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. | |||||||||||||||
19 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. | |||||||||||||||
20~27 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. | |||||||||||||||
28 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. | |||||||||||||||
29 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. | |||||||||||||||
30 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
31 | NC(GND) | No connection |
通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。