首页 产品介绍 OLED显示屏 图形 OLED 显示屏 WEO012864AH

128x64 1.54寸 COG OLED模块 (SH1106)

型号 WEO012864AH

►类型:图形OLED
►结构:COG
►尺寸:1.54寸
►128 x 64 点阵
►IC:SH1106
►3V电源电压
►1/64 duty
►接口:6800,8080,SPI,I2C
►发光颜色: 白色 / 黄色

产品叙述

WEO012864AH是一款1.54寸128x64图型COG OLED显示屏。此COG OLED模块内置SH1106控制器IC可支持I2C、4线SPI串行接口和6800、8080并列接口。逻辑电压范围为1.65V~3.3V,典型值为3.0V,显示电压范围为6.4V~13V,典型值为12.5V,驱动方式1/64 duty。华凌光电的WEO012864AH系列1.54吋OLED模块非常适合各种应用,包括医疗设备 (血氧机)、消费性电子产品 (MP3、无线麦克风接收器)、智能家电、检测设备(USB电压电流检测器)和工业自动化。

主要特点和优点
高质量显示屏:WEO012864AH 系列提供高质量 OLED 显示屏,具有出色的色彩精度、高对比度度(10,000:1)和分辨率(128x64 dots)。
小巧尺寸:模块采用 1.54 寸的小尺寸设计,非常适合便携式设备和穿戴式装置。

应用:
医疗设备:WEO012864AH 系列非常适合用于血糖仪、血压计和其他医疗设备等医疗设备。
消费性电子产品:此模块适用于各种消费性电子产品,包括智能手表、健身追踪器、电子游标卡尺和其他穿戴式装置。
工业自动化:OLED显示器可用于工业自动化应用,例如温度和湿度传感器以及其他监控设备。
智慧家庭设备:此模块可用于智能家庭设备,例如照明系统和其他物联网设备。

此模块工作温度为-40℃至+ 80℃,储存温度为-40℃至+85℃。工作温度范围为-40℃至+80℃; 其储存温度范围为-40℃至+85℃。 WEO012864AH系列有不同的ZIF FPC; 目前,我们提供24 pin和30 pin可选,如果客户需要客制化FPC,欢迎与我们联系。

WEO012864AH 非常适合脉搏血氧仪、无线麦克风接收器和 USB 电压表。

规格图

128x64 OLED Display, 128x64 OLED LCD, OLED Module 128x64, OLED Display 128x64 (SH1106) - WEO012864AH

Data source ref:WEO012864AHWPP3N00000

产品规格

规格说明

项目 规格说明 单位
点阵(分辨率) 128 × 64
模块尺寸 42.04 × 27.22 × 1.41 mm
有效区域 35.05 × 17.51 mm
像素大小 0.249 × 0.249 mm
像素间距 0.274 × 0.274 mm
显示模式 Passive Matrix 被动矩阵
显示颜色 单色
驱动方式 1/64 Duty
IC SH1106
接口 6800,8080,4-wire SPI,I2C
尺寸 1.54 寸

最大绝对额定值

参数 符号 最小值 最大值 单位
逻辑电源电压 VDD1 -0.3 3.6 V
显示电源电压 VPP -0.3 14.5 V
工作温度 TOP -40 +80 °C
储存温度 TSTG -40 +85 °C

电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VDD1 1.65 3.0 3.3 V
显示电源电压 VPP 6.4 12.5 13.0 V
输入高准位 VIH 0.8×VDD1 VDD1 V
输入低准位 VIL VSS 0.2×VDD1 V
输出高准位 VOH 0.8×VDD1 VDD1 V
书出低准位 VOL VSS 0.2×VDD1 V
Display 50% Pixel on IPP VPP =12.5V 13 20 mA

Pin功能定义

No. 符号 功能说明
1 ESD_GND ESD Ground pin
2 VSS Ground.
3 VSS Ground.
4 NC No connection
5 VDD1 Power supply input
6 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
7 IM2
8 /CS This pad is the chip select input. When /CS = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 /RES This is a reset signal input pad. When /RES is set to “L”, the settings are initialized. The reset operation is performed by the /RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 /WR
(R/W)
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/= “H”: Read.
When R/W= “L”: Write.
12 E/RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the /RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When /RD = “H”: Enable.
When /RD = “L”: Disable.
13-20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. It could be supplied externally.
A capacitor should be connected between this pad and VSS.
24 ESD_GND ESD Ground pin
go top
close

我们重视您的隐私

通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。

我们重视您的隐私

Winstar 及部分第三方在 www.winstar.com.tw 上使用 cookies。关于 cookie 的种类、用途及相关第三方的详细信息,请参见下文及我们的《Cookie 政策》。请点击“允许全部”来同意我们使用 cookies,以确保您在我们网站上获得最佳体验。您也可以设置您的偏好或拒绝 cookies(必要的 cookies 除外)。

管理同意声明

永久启用
必要的 Cookie

这些 Cookie 是必不可少的,以便让您在浏览网站并使用其功能上有更好地体验,例如设置您的隐私偏好、登录或填写窗体。

分析 Cookie

这些也被称为「统计cookie」,用于收集您使用网站的信息,例如您访问了哪些页面以及点击了哪些连结。查看详细信息