우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
WEO064128B 시리즈 1.3인치 OLED 디스플레이 모듈은 탁월한 성능과 유연한 통합 능력을 제공하여 게이밍 주변기기, 스마트 홈 디바이스, 산업 제어 시스템 등 다양한 요구 사항을 충족합니다. 높은 대비 비율, 신뢰성 및 낮은 전력 소비로 고효율 제품을 설계하는 엔지니어에게 이상적인 선택입니다.
WEO064128B 시리즈 1.3인치 OLED 디스플레이 모듈은 고품질과 안정적인 성능으로 다영역 설계 과제를 쉽게 해결하고 제품 개발을 가속화합니다. 게이밍, 스마트 홈 또는 산업용 응용 프로그램에 중점을 두든 이 모듈은 귀하의 요구에 완벽하게 부합합니다.
자세한 정보를 원하시면 지금 바로 연락주세요. 차세대 제품 설계에 혁신을 불러일으켜 보세요!
Data source ref: WEO064128BWAP3N00000
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 (해상도) | 64 x 128 | Dots |
모듈 치수 | 17.1 × 35.80 × 1.41 | mm |
활성 영역 | 14.06 × 29.42 | mm |
도트 크기 | 0.20 × 0.21 | mm |
도트 피치 | 0.22 × 0.23 | mm |
디스플레이 모드 | 패시브 매트릭스 | |
디스플레이 색상 | Monochrome | |
Drive Duty | 1/64 Duty | |
IC | SH1107 | |
인터페이스 | 4-wire SPI , I2C | |
크기 | 1.3 인치 |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 3.6 | V |
Supply Voltage for Display | VPP | 7.0 | 17.0 | V |
작동 온도 | TOP | -40 | +80 | °C |
보관 온도 | TSTG | -40 | +85 | °C |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 1.65 | 3.0 | 3.5 | V |
Supply Voltage for Display | VPP | - | 7.0 | 13.0 | 13.5 | V |
Input High Volt. | VIH | - | 0.8×VDD | - | VDD | V |
Input Low Volt. | VIL | - | VSS | - | 0.2×VDD | V |
Output High Volt. | VOH | - | 0.8×VDD | - | VDD | V |
Output Low Volt. | VOL | - | VSS | - | 0.2×VDD | V |
Display 50% Pixel on | IPP | VPP=13V | - | 10 | 15 | mA |
No. | 기호 | 기능 |
---|---|---|
1 | VSS | Ground. |
2 | D1 | When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). |
3 | D0 | |
4 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: Data. A0 = “L”: Command In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
5 | ___ RES |
This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. |
6 | __ CS |
This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data/command I/O is enabled. |
7 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 15.625uA. |
8 | IM1 | These are the MPU interface mode select pads. IM1 connect to VDD is I2C interface. IM1 connect to VSS is 4-wire SPI interface. |
9 | VDD | Power supply for logic and input. |
10 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
11 | VPP | This is the most positive voltage supply pad of the chip. It should be supplied externally. |
12 | VSS | Ground. |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책