我们重视您的隐私
通过点击「允许所有 Cookie」，代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。
产品叙述
WF101JSYAHLNN0 是一款10.1寸横屏模式 超高亮度IPS TFT LCD 模块, 带有1024x600 pixels高分辨率。 WF101J 模块内建EK79001HN和EK73215BCGA驱动IC，支持LVDS接口、对比度为800 (typical value)、亮度1100 nits (typical value)、长宽比16:9，模块采防眩光玻璃表面。此款10.1”IPS TFT相较于 TN TFT有较宽的视角，模块视角范围为左:85 / 右:85 / 上:85 / 下:85 度 (typical value)。
此模块电源电压(VDD) 范围3.0V ~3.6V，典型值为 3.3V;其工作电压为-20℃ ~ +70℃，储存温度-30℃ ~+80℃。如果客户没有高亮度需求请选择P/N: WF101JTYAHLNN0 型号。
规格图
产品规格
规格说明
| 项目 | 规格 | 单位 |
|---|---|---|
| 显示尺寸(对角线) | 10.1 | 寸 |
| 点阵(分辨率) | 1024 RGB x 600 | dots |
| 模块尺寸 | 235(W) x 143(H) x 5.05(D) | mm |
| 有效区域 | 222.72 (H) x 125.28(V) | mm |
| 点间距 | 0.2175(W) x 0.2088(H) | mm |
| LCD类型 | IPS TFT 全透 | |
| 接口 | LVDS | |
| 驱动IC | EK79001HN + EK73215BCGA 或兼容IC | |
| 视角 | 85/85/85/85 | |
| 长宽比 | 16:9 | |
| 背光类型 | LED, 白光 | |
| 触控面板类型 | 无触控面板 | |
| 表面 | 防眩光 | |
最大绝对额定值
| 项目 | 符号 | 最小值 | 典型值 | 最大值 | 单位 |
|---|---|---|---|---|---|
| 工作温度 | TOP | -20 | － | +70 | ℃ |
| 储存温度 | TST | -30 | － | +80 | ℃ |
电气特性
典型操作条件 (At Ta = 25 °C,)
| 项目 | 符号 | 最小值 | 典型值 | 最大值 | 单位 |
|---|---|---|---|---|---|
| LCD数字电源电压 | VDD | 3 | 3.3 | 3.6 | V |
| 模拟电源电压 | AVDD | 9.89 | 10.2 | 10.5 | V |
| Gate On 供电电压 | VGH | 19.4 | 20.0 | 20.6 | V |
| Gate Off 供电电压 | VGL | -10.3 | -10.0 | -9.7 | V |
| 一般供电电压 | VCOM | 4.0 | 4.3 | 4.6 | V |
| 逻辑输入高电压 | VIH | 0.7 VDD | - | VDD | V |
| 逻辑输入低电压 | VIL | 0 | - | 0.3 VDD | V |
Pin功能定义
| Pin No. | 符号 | 功能说明 |
|---|---|---|
| 1 | VCOM | Common voltage |
| 2 | VDD | Digital power |
| 3 | VDD | Digital power |
| 4 | NC | Not connect |
| 5 | Reset | Global reset pin. Active low to enter reset state. Suggest to connecting with an RC reset circuit for stability. Normally pull high. (R=10KΩ，C=1μF) |
| 6 | STBYB | Standby mode, normally pull high STBYB=”1”, normal operation STBYB=”0”,timing control, source driver will turn off, all output are high-Z |
| 7 | GND | Digital ground |
| 8 | RXIN0- | Negative LVDS differential data inputs |
| 9 | RXIN0+ | Positive LVDS differential data inputs |
| 10 | GND | Digital ground |
| 11 | RXIN1- | Negative LVDS differential data inputs |
| 12 | RXIN1+ | Positive LVDS differential data inputs |
| 13 | GND | Digital ground |
| 14 | RXIN2- | Negative LVDS differential data inputs |
| 15 | RXIN2+ | Positive LVDS differential data inputs |
| 16 | GND | Digital ground |
| 17 | RXCLKN- | Negative LVDS differential clock inputs |
| 18 | RXCLKN+ | Positive LVDS differential clock inputs |
| 19 | GND | Digital ground |
| 20 | RXIN3- | Negative LVDS differential data inputs |
| 21 | RXIN3+ | Positive LVDS differential data inputs |
| 22 | GND | Digital ground |
| 23 | NC | Not connect |
| 24 | NC | Not connect |
| 25 | GND | Digital ground |
| 26 | NC | Not connect |
| 27 | NC | Not connect |
| 28 | SELB | 6-bit/8-bit input select SELB = L , 8-bit ; SELB = H , 6-bit |
| 29 | AVDD | Analog power |
| 30 | GND | Digital ground |
| 31 | LED- | LED Cathode |
| 32 | LED- | LED Cathode |
| 33 | L/R | Left or right display control |
| 34 | U/D | Up / down display control |
| 35 | VGL | Negative power for TFT |
| 36 | NC | Not connect |
| 37 | NC | Not connect |
| 38 | VGH | Positive power for TFT |
| 39 | LED+ | LED Anode |
| 40 | LED+ | LED Anode |
When L/R=”1”,set left to right scan direction.
When U/D=”0”,set top to bottom scan direction.
When U/D=”1”,set bottom to top scan direction.