首页 产品介绍 LCD显示屏 COG液晶模块 WO24064A1

240x64 COG点阵液晶屏

型号 WO24064A1

►COG LCD显示模块
►类型: 图形
►结构: COG
►尺寸: 5.18英寸
►240x64点阵
►IC: ST7565P
►3.3V电源电压
►接口:6800/8080/SPI

规格图

LCD COG Module 240x64 - Winstar WO24064A1
Data source ref:WO24064A1-TFH#

产品规格

Pin功能定义

Pin No. 符号 Level 说明
1 NC   No connection
2 FR O This is the liquid crystal alternating current signal terminal.
3 CL I/O This is the display clock input terminal
The following is true depending on the M/S and CLS status.
4 /DOF O This is the LCD blanking control terminal.
5 /CS1 I This is the chip select signal. When /CS1 = “L” and CS2 = “H”, then the chip Select becomes active, and data/command I/O is enabled.
6 CS2 I
7 /RES I When /RES is set to “L”, the register settings are initialized (cleared).
The reset operation is performed by the /RES signal level.
8 A0 I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.
9 /WR I When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
The signals on the data bus are latched at the rising edge of the /WR signal.
When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
When R/W = “H”: Read.
When R/W = “L”: Write.
10 /RD I When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
The data bus is in an output status when this signal is “L”.
When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
This is the enable clock input terminal of the 6800 Series MPU.
11~18 DB0~DB7 I/O Data bus
19 VDD P Power supply
20 VSS P Ground
21 Vout O DC/DC voltage converter. Connect a capacitor between this terminal and VSS or VDD
22 C3+ O DC/DC voltage converter
23 C1-
24 C1+
25 C2+
26 C2-

27
V4 P This is a multi-level power supply for the liquid crystal drive. The voltage Supply applied is determined by the liquid crystal cell, and is changed through the use of a resistive voltage divided or through changing the impedance using an op. amp.
Voltage levels are determined based on Vss, and must maintain the relative magnitudes shown below.
V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧Vss
28 V3
29 V2
30 V1
31 V0
32 VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
IRS = “L” : the V0 voltage regulator internal resistors are not used.
IRS = “H” : the V0 voltage regulator internal resistors are used.
33 C86 I This is the MPU interface selection pin.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface.
34 P/S I This pin configures the interface to be parallel mode or serial mode.
P/S = “H”: Parallel data input/output.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:
P/S Data/Command Data Read/Write Serial Clock
“H” A0 D0 to D7 /RD, /WR X
“L” A0 SI (D7) Write only SCL (D6)
When P/S = “L”, D0 to D5 must be fixed to “H”.
/RD (E) and /WR (R/W) are fixed to either “H” or “L”.
The serial access mode does NOT support read operation.
35 NC   No connection
36 NC   No connection

规格说明

项目 标准尺寸 单位
点阵(分辨率) 240 x 64
模块尺寸 142.5 x 51.7 x 14.9(MAX) mm
检视区域 130.2 x 37.6 mm
有效区域 127.17 x 33.89 mm
点大小 0.50 x 0.50 mm
点间距 0.53 x 0.53 mm
驱动方式 1/65
背光类型 LED
IC ST7565P
接口 6800/8080/4-Line SPI

最大绝对额定值

项目 符号 最小值 典型值 最大值 单位
工作温度 TOP -20 +70
储存温度 TST -30 +80
电源电压 VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0,VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1,V2,V3,V4 -0.3 V0+0.3 V

电气特性

项目 符号 条件 最小值 典型值 最大值 单位
逻辑电源电压 VDD-VSS 3.0 3.3 3.6 V
LCM电源电压 V0-VSS Ta=-20℃
Ta=25℃
Ta=70℃

10.

11.0

11.3
V
V
V
输入高电压 VIH 0.8 VDD VDD V
输入低电压 VIL VSS 0.2VDD V
输出高电压 VOH 0.8VDD VDD V
输出低电压 VOL VSS 0.2VDD V
供电电流(不包括LED背光) IDD VDD=3.3V 1.5 2.5 mA

Search Keyword: lcd 240x64, lcd 240 x 64, 240x64 lcd, 240 x 64 lcd
go top
close

我们重视您的隐私

通过点击「允许所有 Cookie」,代表您同意在您的设备上存储 Cookie 以增强网站浏览体验、分析网站使用情况并协助我们的营销和网站效能优化工作。您可以在我们的隐私权政策中找到有关于此的更多信息。

我们重视您的隐私

Winstar 及部分第三方在 www.winstar.com.tw 上使用 cookies。关于 cookie 的种类、用途及相关第三方的详细信息,请参见下文及我们的《Cookie 政策》。请点击“允许全部”来同意我们使用 cookies,以确保您在我们网站上获得最佳体验。您也可以设置您的偏好或拒绝 cookies(必要的 cookies 除外)。

管理同意声明

永久启用
必要的 Cookie

这些 Cookie 是必不可少的,以便让您在浏览网站并使用其功能上有更好地体验,例如设置您的隐私偏好、登录或填写窗体。

分析 Cookie

这些也被称为「统计cookie」,用于收集您使用网站的信息,例如您访问了哪些页面以及点击了哪些连结。查看详细信息