Home Produtos Display OLED Display OLED Gráfico WEO012864AC

Tela OLED Display Gráfico 128x64 de 0,96 polegadas

Model No. WEO012864AC

►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 0,96 polegadas
►Matriz de pontos 128x64
►IC:SSD1315
►Alimentação 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Display Color: Branco / Amarelo

Descrição

DRAWING

128x64 OLED Display, 128x64 OLED LCD, OLED Module 128x64, OLED Display 128 x 64 - WEO012864AC
Data source ref: WEO012864ACWPP3N00000

SPECIFICATIONS

Dados Mecânicos

Item Dimensão Unidade
Matriz de pontos 128 x 64
Dimensão do módulo 26.70 × 19.26 ×1.26 mm
Área ativa 21.74 × 10.86 mm
Tamanho do ponto 0.15 × 0.15 mm
Distância entre pontos 0.17 × 0.17 mm
Modo de exibição Passive Matrix
Cor de exibição Monochrome
Drive Duty 1/64 Duty
Controller IC SSD1315
Interface 6800, 8080, SPI, I2C
Tamanho 0,96 polegadas

Classificações Máximas Absolutas

Parameter Símbolo Valor Min Valor Máximo Unidade
Supply Voltage for Logic VDD 0 4.0 V
Power supply for charge pump circuit VBAT 0 6.0 V
Supply Voltage for Display VCC 0 15.0 V
Temperatura de operação TOP -40 +80 °C
Temperatura de armazenamento TSTG -40 +85 °C

Características Eletrônicas

DC Características Eletrônicas

Item Símbolo Condição Valor Min Valor Típico Valor Máximo Unidade
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Charge Pump Regulator Supply Voltage VBAT 2.4 3.5 5.0 V
Supply Voltage for Display VCC 6.0 12.0 12.5 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump
VPP
7.0 7.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL 0 0.2xVDD V
Output High Volt. VOH 0.9xVDD VDD V
Output Low Volt. VOL 0 0.1xVDD V
Operating Current for VCC (50% display ON) (VCC Supplied Externally) ICC VCC=12V 10 20 mA
50% checkerboard operating Current (VCC Generated by Internal DC/DC) IBAT 15 30 mA

Função do pino de interface

No. Símbolo Função
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
7 NC NC
8 VSS Ground pin. It must be connected to external ground.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
  BS0 BS1 BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
27 VCOMH The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
go top
close

Valorizamos sua privacidade

Ao clicar em "Permitir todos os cookies", você concorda com o armazenamento de cookies no seu dispositivo para melhorar a navegação no site, analisar o uso do site e auxiliar nossos esforços de marketing e desempenho. Você pode encontrar mais informações sobre esse assunto em nossa política. Política de privacidade

Valorizamos sua privacidade

A Winstar e certos terceiros utilizam cookies no site www.winstar.com.tw. Os detalhes sobre os tipos de cookies, sua finalidade e as partes terceiras envolvidas estão descritos abaixo e em nossa Política de Cookies. Clique em “Permitir todos” para consentir o uso de cookies e obter a melhor experiência possível em nossos sites. Você também pode definir suas preferências ou rejeitar cookies (exceto os estritamente necessários).

Gerenciar preferências de consentimento

Sempre ativo
Cookies essenciais

Esses cookies são essenciais para permitir que você navegue pelo site e utilize seus recursos, como definir suas preferências de privacidade, fazer login ou preencher formulários.

Cookies de análise

Também conhecidos como "cookies estatísticos", esses cookies coletam informações sobre como você utiliza um site, como quais páginas você visitou e em quais links você clicou. Veja os detalhes.