Accueil Produits Écran OLED Afficheur OLED Graphique WEO012864AC

Écran OLED graphique COG 0,96 pouces 128x64 avec SSD1315

N° de modèle WEO012864AC

►Type: Graphique
►Structure: COG
►Dimension: 0.96 pouces
►Matrice de points 128 x 64
►IC:SSD1315
►Alimentation 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Couleur d'affichage: Blanc / Jaune

Description

DESSIN

128x64 OLED Display, 128x64 OLED LCD, OLED Module 128x64, OLED Display 128 x 64 - WEO012864AC
Data source ref: WEO012864ACWPP3N00000

SPÉCIFICATIONS

Fonction PIN sur l'interface

No. Symbole Fonction
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
7 NC NC
8 VSS Ground pin. It must be connected to external ground.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
  BS0 BS1 BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
27 VCOMH The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

Spécifications générales

Article Dimensions Unité
Matrice de points 128 x 64
Dimensions du module 26.70 × 19.26 ×1.26 mm
Zone active 21.74 × 10.86 mm
Taille des points 0.15 × 0.15 mm
Pas des points 0.17 × 0.17 mm
Mode d'affichage Matrice passive
Couleur d'affichage Monochrome
Drive Duty 1/64 Duty
Controller IC SSD1315
Interface 6800, 8080, SPI, I2C
Diagonale 0.96 pouces

Valeurs nominales maximales absolues

Parameter Symbole Valeur min Valeur max Unité
Supply Voltage for Logic VDD 0 4.0 V
Power supply for charge pump circuit VBAT 0 6.0 V
Supply Voltage for Display VCC 0 15.0 V
Température de fonctionnement TOP -40 +80 °C
Température de stockage TSTG -40 +85 °C

Caractéristiques électroniques

DC Caractéristiques électroniques

Article Symbole État Valeur min Valeur type Valeur max Unité
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Charge Pump Regulator Supply Voltage VBAT 2.4 3.5 5.0 V
Supply Voltage for Display VCC 6.0 12.0 12.5 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump
VPP
7.0 7.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL 0 0.2xVDD V
Output High Volt. VOH 0.9xVDD VDD V
Output Low Volt. VOL 0 0.1xVDD V
Operating Current for VCC (50% display ON) (VCC Supplied Externally) ICC VCC=12V 10 20 mA
50% checkerboard operating Current (VCC Generated by Internal DC/DC) IBAT 15 30 mA

 

Search keyword: 128x64 oled, oled 128x64, 0.96 oled, 0.96" oled, 0.96 pouces oled, oled 0.96, oled 0.96"
go top
close

Nous valorisons votre confidentialité

En cliquant sur "Autoriser tous les cookies", vous acceptez le stockage de cookies sur votre appareil pour améliorer la navigation sur le site, analyser l'utilisation du site et aider dans nos efforts de marketing et de performance. Vous pouvez trouver plus d'informations à ce sujet dans notre politique. Politique de confidentialité

Nous valorisons votre confidentialité

Winstar et certains tiers utilisent des cookies sur www.winstar.com.tw. Les détails concernant les types de cookies, leur objectif et les tiers impliqués sont décrits ci-dessous et dans notre Politique relative aux cookies. Veuillez cliquer sur « Autoriser tout » pour consentir à l'utilisation de cookies et profiter de la meilleure expérience possible sur nos sites. Vous pouvez également définir vos préférences ou refuser les cookies (sauf les cookies strictement nécessaires).

Gérer les préférences de consentement

Toujours actif
Cookies essentiels

Ces cookies sont essentiels pour vous permettre de naviguer sur le site et d'utiliser ses fonctionnalités, telles que la définition de vos préférences en matière de confidentialité, la connexion ou le remplissage de formulaires.

Cookies analytiques

Également connus sous le nom de « cookies statistiques », ces cookies collectent des informations sur la façon dont vous utilisez un site Web, comme les pages que vous avez visitées et les liens sur lesquels vous avez cliqué. Voir les détails.