Ana sayfa Ürünler OLED Ekran Grafik OLED Ekran WEO012864AC

0.96 inç COG Grafik OLED Ekran 128x64

Model No. WEO012864AC

►Türü : Grafik
►Yapı : COG
►128 x 64 dot matrisi
►IC:SSD1315
►3V güç sağlayıcı
►1/64 görev
►Ara yüz : 6800, 8080, SPI, I2C
►OLED Rengi: Beyaz / Sarı

Açıklama

ÇIZIM

128x64 OLED Display, 128x64 OLED LCD, OLED Module 128x64, OLED Display 128 x 64 - WEO012864AC
Data source ref: WEO012864ACWPP3N00000

AYRINTILAR

Genel Özellikler

Kalem Modül ölçüleri Birim
Nokta Matrisi 128 x 64
Modül ölçüleri 26.70 × 19.26 ×1.26 mm
Aktif alan 21.74 × 10.86 mm
Nokta boyutu 0.15 × 0.15 mm
Nokta sıklığı 0.17 × 0.17 mm
Display Mode Pasif Matrisli
Display Renk Monokrom
Drive Duty 1/64 Duty
Kontrolör IC SSD1315
Arayüz 6800, 8080, SPI, I2C
Boyut (Köşegen) 0.96 inç

Maksimum Değerler

Parameter Sembol Minumum Deger Maksimum Deger Birim
Supply Voltage for Logic VDD 0 4.0 V
Power supply for charge pump circuit VBAT 0 6.0 V
Supply Voltage for Display VCC 0 15.0 V
Çalışma Sıcaklığı TOP -40 +80 °C
Saklama Sıcaklığı TSTG -40 +85 °C

Elektronik Özellikleri

DC Elektronik Özellikleri

Kalem Sembol Durum Minumum Deger Tipik Deger Maksimum Deger Birim
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Charge Pump Regulator Supply Voltage VBAT 2.4 3.5 5.0 V
Supply Voltage for Display VCC 6.0 12.0 12.5 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump
VPP
7.0 7.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL 0 0.2xVDD V
Output High Volt. VOH 0.9xVDD VDD V
Output Low Volt. VOL 0 0.1xVDD V
Operating Current for VCC (50% display ON) (VCC Supplied Externally) ICC VCC=12V 10 20 mA
50% checkerboard operating Current (VCC Generated by Internal DC/DC) IBAT 15 30 mA

Arayüz Pin Fonksiyonlari

No. Sembol Fonksiyon
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
7 NC NC
8 VSS Ground pin. It must be connected to external ground.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
  BS0 BS1 BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
27 VCOMH The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
go top
close

Gizliliğinize değer veriyoruz

"Tüm Çerezlere İzin Ver" seçeneğine tıklayarak, site gezinmesini geliştirmek, site kullanımını analiz etmek ve pazarlama ve performans çalışmalarımıza yardımcı olmak amacıyla cihazınıza çerezlerin kaydedilmesini kabul etmiş olursunuz. Bu konu hakkında daha fazla bilgiye politikamızda ulaşabilirsiniz. Gizlilik Politikası

Gizliliğinize değer veriyoruz

Winstar ve bazı üçüncü taraflar www.winstar.com.tw adresinde çerezler kullanmaktadır. Çerez türleri, amaçları ve ilgili üçüncü taraflar hakkındaki ayrıntılar aşağıda ve Çerez Politikamızda açıklanmaktadır. Web sitemizde en iyi deneyimi yaşamak için çerez kullanımına izin vermek amacıyla “Hepsine İzin Ver” düğmesine tıklayabilirsiniz. Ayrıca tercihlerinizi ayarlayabilir veya zorunlu olanlar haricindeki çerezleri reddedebilirsiniz.

Rıza tercihlerini yönet

Her zaman aktif
Gerekli Çerezler

Bu çerezler, web sitesinde gezinmenizi ve gizlilik tercihlerinizi ayarlamak, oturum açmak veya formları doldurmak gibi özellikleri kullanmanızı sağlamak için gereklidir.

Analitik Çerezler

“İstatistik çerezleri” olarak da bilinen bu çerezler, bir web sitesini nasıl kullandığınız hakkında bilgi toplar; örneğin, hangi sayfalara girdiğinizi ve hangi bağlantılara tıkladığınızı. Ayrıntılara bakın.