Doświadcz wyjątkowej jakości wizualnej z modułem wyświetlacza OLED o przekątnej 5,5 cala od Winstar (WEX025664D)
Odkryj nową erę doskonałości wizualnej dzięki modułowi COF OLED o przekątnej 5,5 cala od Winstar (WEX025664D). Posiada on imponującą rozdzielczość 256x64 punktów, wbudowany układ SSD1322 i obsługuje interfejsy 6800/8080 8-bit oraz 3/4-line SPI.
Pracując przy zasilaniu 3V i wykorzystując metodę sterowania 1/64, ten moduł OLED o przekątnej 5,5 cala zapewnia imponujący stosunek kontrastu 10000:1 i obsługuje 4-bitową skalę szarości, co gwarantuje wyraziste i szczegółowe obrazy. Zakres temperatury operacyjnej od -40℃ do +80℃, w połączeniu z zakresem temperatury przechowywania od -40℃ do +85℃, sprawia, że jest wszechstronny w różnorodnych środowiskach.
Seria COF 5,5-calowych wyświetlaczy od Winstar doskonale sprawdzi się w wielu zastosowaniach, takich jak urządzenia ścienne/metro, automatyzacja domowa, systemy POS, konfiguracje Cloud/IoT, urządzenia przenośne, inteligentne urządzenia technologiczne, systemy energetyczne, wyświetlacze samochodowe, systemy komunikacyjne i urządzenia medyczne. Bezproblemowo przejdź do wyświetlaczy OLED z tradycyjnych wyświetlaczy STN, korzystając z bogatej gamy formatów pikseli punktowych i nowoczesnej technologii od Winstar.
Poznaj dodatkowe opcje dostosowane do Twoich potrzeb:
WEN025664D: W komplecie z ramą i PCB dla dodatkowego ułatwienia.
WEN025664D-CTP: Podnieś interakcję użytkownika dzięki ramie, PCB i panelowi dotykowemu CTP.
Przemień swoje aplikacje dzięki 5,5-calowemu wyświetlaczowi OLED od Winstar, szczytowi innowacji w dziedzinie wizualizacji. Bezproblemowo awansuj do przyszłości technologii wyświetlania.
Rysunek
Data source ref: WEX025664DWPP3N00000
Specyfikacja
Mechanical Data
Item
Dimension
Unit
Dot Matrix
256 x 64 Dots
-
Module dimension
146.0 × 45.0 × 2.01
mm
Active Area
135.65 × 33.89
mm
Pixel Size
0.50 × 0.50
mm
Pixel Pitch
0.53 × 0.53
mm
Display Mode
Passive Matrix
Display Color
Monochrome
Drive Duty
1/64 Duty
Gray Scale
4 bits
IC
SSD1322
Interface
6800, 8080, SPI
Size
5.5 inch
Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
Supply Voltage for Logic
VDD
-0.5
2.75
V
Low voltage power supply
VCI
-0.3
4.0
V
Power supply for I/O pins
VDDIO
-0.5
VCI
V
Supply Voltage for Display
VCC
-0.5
21.0
V
Operating Temperature
TOP
-40
+80
°C
Storage Temperature
TSTG
-40
+85
°C
Electronical Characteristics
DC Electrical Characteristics
Item
Symbol
Condition
Min
Typ
Max
Unit
Supply Voltage for Logic
VDD
-
2.4
2.5
2.6
V
Power Supply for I/O pins
VDDIO
-
1.65
3.0
VCI
V
Low voltage power supply
VCI
-
2.4
3.0
3.5
V
Supply Voltage for Display
VCC
-
10.0
18.0
18.5
V
High Level Input
VIH
-
0.8×VDDIO
-
VDDIO
V
Low Level Input
VIL
-
0
-
0.2×VDDIO
V
High Level Output
VOH
-
0.9×VDDIO
-
VDDIO
V
Low Level Output
VOL
-
0
-
0.1×VDDIO
V
Display 30% Pixel on
ICC
VCC =18V
-
40
60
mA
Interface Pin Function
No.
Symbol
Function
1
N.C.
The N.C. pin between function pins are reserved for compatible and flexible design.
2
VSS
Ground.
3
VCC
Power supply for panel driving voltage.
This is also the most positive power voltage supply pin.
4
VCOMH
COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
5
VLSS
Analog system ground pin.
6~13
D7~D0
These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW. (Except for D2 pin in SPI mode)
14
E/RD#
This pin is MCU interface input.
When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When connecting to an 8080-microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin E(RD#) must be connected to VSS.
15
R/W#
This pin is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as
Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial interface is selected, this pin R/W (WR#) must be connected to VSS.
16
BS0
MCU bus interface selection pins. Select appropriate logic setting as described in the following table.
BS[1:0]
Bus Interface Selection
00
4 line SPI
01
3 line SPI
10
8-bit 8080 parallel
11
8-bit 6800 parallel
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
17
BS1
18
D/C#
This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the content at D[7:0] will be interpreted as command.
19
CS#
This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW.
20
RES#
This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
21
FR
This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually.
22
IREF
This pin is the segment output current reference pin.
A resistor should be connected between this pin and VSS to maintain the current around 10uA.
23
N.C.
The N.C. pin between function pins are reserved for compatible and flexible design.
24
VDDIO
Power supply for interface logic level. It should be matched with the MCU interface voltage level.
25
VDD
Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS.
26
VCI
Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
27
VSL
This is segment voltage reference pin.
When external VSL is used, connect with resistor and diode to ground.
28
VLSS
Analog system ground pin.
29
VCC
Power supply for panel driving voltage.
This is also the most positive power voltage supply pin.
30
N.C.
The N.C. pin between function pins are reserved for compatible and flexible design.
Klikając „Zezwól na wszystkie pliki cookie”, zgadzasz się na przechowywanie plików cookie na swoim urządzeniu w celu usprawnienia nawigacji po witrynie, analizy korzystania z witryny oraz wspierania naszych działań marketingowych i dotyczących wydajności. Więcej informacji na ten temat znajdziesz w naszej polityce. Polityka prywatności