우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
WINSTAR 모델 WFN0240A2T0GADNN000 은 실내와 실외 환경 모두에서 우수한 가독성을 제공하도록 설계된 2.4인치 반투과형 TFT-LCD 모듈입니다. 240×320 해상도와 ST7789 드라이버 IC를 탑재하여 안정적인 성능과 손쉬운 시스템 통합을 지원합니다. MCU, SPI, RGB 등 다양한 인터페이스를 지원하여 엔지니어에게 높은 설계 유연성을 제공합니다. 반사 방지 표면 처리와 -20℃~+70℃ 의 동작 온도 범위를 갖추어 휴대용 기기, 산업용 컨트롤러, 의료 장비 등에서 안정적인 가독성과 내구성이 요구되는 응용에 적합합니다.
항목 | 치수 | 단위 |
---|---|---|
크기 (대각선) | 2.4 | 인치 |
도트 매트릭스 (해상도) | 240 × RGB × 320(TFT) | dots |
모듈 치수 | 42.72 × 60.26 × 2.63 | mm |
활성 영역 | 36.72 × 48.96 | mm |
도트 피치 | 0.153 × 0.153 | mm |
LCD 유형 | TFT, 백색, 반투과성 | |
시야각 | 3 O'clock | |
TFT 인터페이스 | 8/9/16/18Bit MCU 3/4SPI+16/18Bit RGB 3-line/4-line Serial |
|
역광 타입 | LED,백색 | |
TFT 드라이버 IC | ST7789 또는 이와 동등한 | |
터치 패널 | 터치패널(스크린)이 없는 | |
표면 | 눈부심 방지 |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
작동 온도 | TOP | -20 | - | +70 | ℃ |
보관 온도 | TST | -30 | - | +80 | ℃ |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
Digital Supply Voltage | VCI | 2.4 | 3.3 | 3.6 | V |
Supply Voltage (Logic) | IOVCC | 1.65 | 1.8 | 3.3 | V |
Normal mode Current consumption | IDD | -- | 5 | 10 | mA |
Level input voltage | VIH | 0.7 IOVCC | IOVCC | V | |
VIL | GND | 0.3 IOVCC | V | ||
Level output voltage | VOH | 0.8 IOVCC | IOVCC | V | |
VOL | GND | 0.2 IOVCC | V |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
LED 전류 | - | - | 80 | - | mA |
LED 전압 | VLEDA | 2.7 | 3.1 | 3.3 | V |
LED 수명 | - | 50,000 | - | - | Hr |
Pin No | 기호 | 기능 | I/O |
---|---|---|---|
1 | NC | No connection | -- |
2 | NC | No connection | -- |
3 | NC | No connection | -- |
4 | NC | No connection | -- |
5 | GND | Ground. | P |
6 | GND | Ground. | P |
7 | VCC | Supply voltage(3.3V). | I |
8 | VCC | Supply voltage(3.3V). | I |
9 | IOVCC | Power Supply for I/O System. | I |
10 | SDO | SPI interface output pin. -The data is output on the falling edge of the SCL signal. -If not used, let this pin open. |
O |
11-28 | DB17-DB0 | 18-bit parallel bi-directional data bus for MCU system and RGB i nterface mode. Fix to GND level when not in use |
I/O |
29 | DIN(SDA) | Serial input signal. The data is latched on the rising edge of the SCL signal. fix this pin at IOVCC or GND when not in use. |
I/O |
30 | PCLK | Dot clock signal for RGB interface operation. Fix this pin at IOVCC or GND when not in use. |
I |
31 | DE | Data enable signal for RGB interface operation. fix this pin at IOVCC or GND when not in use. |
I |
32 | HSYNC | Line synchronizing signal for RGB interface operation. fix this pin at IOVCC or GND when not in use. |
I |
33 | VSYNC | Frame synchronizing signal for RGB interface operation. fix this pin at IOVCC or GND when not in use. |
I |
34 | RD | Read enable in 8080 MCU parallel interface. -If not used, please fix this pin at IOVCC or DGND. |
I |
35 | WR(SPI-RS) | -Write enable in MCU parallel interface. Display data/command selection pin in 4-line serial interface. Second Data lane in 2 data lane serial interface. -If not used, please fix this pin at IOVCC or DGND. |
I |
36 | RS(SPI-SCL) | -Display data/command selection pin in parallel interface. -This pin is used to be serial interface clock. RS=’1’: display data or parameter. RS=’0’: command data. -If not used, please fix this pin at IOVCC or DGND. |
I |
37 | CS | Chip select input pin (“Low” enable). fix this pin at IOVCC or GND when not in use. |
I |
38 | RESET | This signal will reset the device and must be applied to properly initialize the chip. |
I |
39 | IM0 | 18-bit parallel bi-directional data bus for MCU system and RGB interface mode. Fix to GND level when not in use |
I |
40 | IM1 | ||
41 | IM2 | ||
42 | NC | No connection | - |
43 | LEDA | Anode pin of backlight | P |
44 | NC | No connection | - |
45 | LEDK | Cathode pin OF backlight | P |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책