우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
WEO012864G는 모듈에 전용용량성 터치 패널이 장착된 가장 인기 있는 2.42인치 그래픽 OLED 디스플레이입니다. 해상도는 128x64 도트로 구성되어 있습니다. 이 모듈은 SSD1309 IC가 내장되어 있으며, 6800/8080 8비트 병렬, I2C 및 4-Wire SPI 인터페이스를 지원하며, 로직 전압은 3V, 디스플레이 전압은 13V, 1/64 듀티 사이클을 가지고 있습니다. 이 WEO012864G 모델은 모듈에 GT911 터치 패널 IC도 내장되어 있으며, I2C 인터페이스를 지원하며 CTP용 감지 포인트가 하나 있습니다. 이 OLED 모듈은 10,000:1의 높은 대비 비율을 특징으로 하며, 더욱 선명한 디스플레이 이미지를 제공합니다.
이 2.42인치 WEO012864G CTP 모델은 스마트 홈 응용 프로그램, 지능형 기술 기기, 에너지 시스템, 계량 장치, 통신 시스템, 의료 기기 등에 이상적입니다. 이 모듈은 -20℃에서 70℃의 온도에서 작동할 수 있으며, 보관 온도는 -30℃에서 80℃로 범위합니다.
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 | 128 x 64 | Dot |
모듈 치수 | 66.8 × 41.3 × 3.71 | mm |
활성 영역 | 55.01 × 27.49 | mm |
도트 크기 | 0.40 × 0.40 | mm |
도트 피치 | 0.43 × 0.43 | mm |
디스플레이 모드 | 패시브 매트릭스 | |
디스플레이 색상 | Monochrome | |
인터페이스 | 8Bits 68xx 80xx / 4-Wire SPI / I2C | |
Drive Duty | 1/64 Duty | |
OLED IC | SSD1309 | |
크기 | 2.42 인치 | |
CTP IC | GT911 | |
터치포인트 | 1 | |
CTP 인터페이스 | I2C | |
표면 | 눈부심 |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4 | V |
Supply Voltage for Display | VCC | 0 | 15 | V |
작동 온도 | TOP | -20 | +70 | °C |
보관 온도 | TSTG | -30 | +80 | °C |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
Power Supply Voltage | VDD | 2.66 | 3.47 | V |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 12.5 | 13.0 | 13.5 | V |
High Level Input | VIH | - | 0.8×VDD | - | - | V |
Low Level Input | VIL | - | - | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | - | V |
Low Level Output | VOL | - | - | - | 0.1×VDD | V |
50% Check Board operating Current | VCC =13.0V | - | 25 | 36 | mA |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
Supply Voltage | VDD | 2.8 | 3.0 | 3.3 | V |
Input High Volt. | VIH | 0.75xVDD | VDD+0.3 | V | |
Input Low Volt. | VIL | -0.3 | - | 0.25xVDD | V |
Output High Volt. | VOH | 0.85xVDD | - | - | V |
Output Low Volt. | VOL | - | - | 0.15xVDD | V |
No. | 기호 | 기능 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | NC(GND) | No connection | |||||||||||||||
2 | VSS | Ground. | |||||||||||||||
3-10 | NC | No connection | |||||||||||||||
11 | VDD | Power supply pin for core logic operation | |||||||||||||||
12 | BS1 | MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select
(1) 0 is connected to VSS (2) 1 is connected to VDD |
|||||||||||||||
13 | BS2 | ||||||||||||||||
14 | NC | No connection | |||||||||||||||
15 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
|||||||||||||||
16 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
17 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
18 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
19 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
20~27 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
28 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
29 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
30 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
31 | NC(GND) | No connection |
No. | 기호 | 기능 |
---|---|---|
1 | GND | Power ground |
2 | VDD | Power supply |
3 | INT | Interrupt signal, active low, asserted to request Host start a new transaction |
4 | SDA | I2C data signal |
5 | SCL | I2C clock signal |
6 | RST | External reset signal, active low |
7 | GND | Power ground |
8 | GND | Power ground |
9 | GND | Power ground |
10 | GND | Power ground |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책