우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
Pin No. | 기호 | Level | 설명 | ||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VG | P | VG is the power of SEG-drivers. | ||||||||||||||||||||
2 | XV0 | P | Negative operating voltage of COM-drivers. | ||||||||||||||||||||
3 | V0 | P | Positive operating voltage of COM-drivers. V0O is the output of the positive Vop generator. V0I is the positive Vop supply of LCD drivers. V0S is the sensor of the positive Vop generator. V0O, V0I & V0S should be separated on ITO and be connected together by FPC. |
||||||||||||||||||||
4 | VM | P | VM is the non-select voltage level of COM-drivers. | ||||||||||||||||||||
5 | VDDA | P | Analog power for internal booster. | ||||||||||||||||||||
6 | VSS | P | Ground | ||||||||||||||||||||
7 | VD1 | P | VD1I is the power source of digital circuits. | ||||||||||||||||||||
8 | VDDI | P | Power of interface I/O circuit. | ||||||||||||||||||||
9 | CSB | Input | Chip select input pin. CSB=“L”: This chip is selected and the MPU interface is active. CSB=“H”: This chip is not selected and the MPU interface is disabled (D[7:0] are high impedance). |
||||||||||||||||||||
10 | IF3 | Input | These pins select interface operation mode.
|
||||||||||||||||||||
11 | IF2 | ||||||||||||||||||||||
12 | IF1 | ||||||||||||||||||||||
13 | RSTB | Input | Reset input pin. When RSTB is “L”, internal initialization procedure is executed. | ||||||||||||||||||||
14 | /RD(E) | Input | Read / Write execution control pin. (This pin is only used in parallel interface) | ||||||||||||||||||||
15 | D7 | I/O | The bi-directional data bus of the MPU interface. When CSB is “H”, they are high impedance. If using serial interface: D0 is the SDA signal in 4-Line & 3-Line interface. D1 is the A0 signal in 4-Line interface |
||||||||||||||||||||
16 | D6 | ||||||||||||||||||||||
17 | D5 | ||||||||||||||||||||||
18 | D4 | ||||||||||||||||||||||
19 | D3 | ||||||||||||||||||||||
20 | D2 | ||||||||||||||||||||||
21 | D1 | ||||||||||||||||||||||
22 | D0 | ||||||||||||||||||||||
23 | NC | No connection | |||||||||||||||||||||
24 | /WR(R/W) | Input | Read / Write execution control pin. (This pin is only used in parallel interface) | ||||||||||||||||||||
25 | A0(SCL) | Input | The function of this pin is different in parallel and serial interface. In parallel interface: A0 is register selection input. A0 = "H": inputs on data bus are display data; A0 = "L": inputs on data bus are command. _ In serial interface: this pad will be used as SCL (serial-clock) input |
||||||||||||||||||||
26 | VSS | P | Ground |
항목 | 치수 | 단위 |
---|---|---|
점의 수 | 240 x 64 | - |
모듈 치수 | 86.2 x 39.3 x 5.1 | mm |
보기 영역 | 80.8 x 24.8 | mm |
활성 영역 | 76.78 x 20.46 | mm |
도트 크기 | 0.30 x 0.30 | mm |
도트 피치 | 0.32 x 0.32 | mm |
듀티 | 1/64 | |
역광 타입 | LED | |
IC | ST7586S | |
인터페이스 | 6800/8080/3-Line/4-Line |
항목 | 기호 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|
작동 온도 | TOP | -20 | - | +70 | ℃ |
보관 온도 | TST | -30 | - | +80 | ℃ |
Digital Power Supply Voltage | VDDI | -0.3 | - | 3.6 | V |
Analog Power supply voltage | VDDA | -0.3 | - | 3.6 | V |
LCD Power supply voltage | V0-XV0 | -0.3 | - | 19 | V |
LCD Power supply voltage | VG | -0.3 | - | 5.5 | V |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
Supply Voltage For Logic | VDD-VSS | - | 3.0 | 3.3 | 3.4 | V |
Supply Voltage For LCM | XV0-V0 | Ta=-20℃ Ta=25℃ Ta=70℃ |
- 9.8 - |
- 10.0 - |
- 10.2 - |
V V V |
Input High Volt. | VIH | - | 0.7 VDD | - | VDD | V |
Input Low Volt. | VIL | - | VSS | - | 0.3VDD | V |
Output High Volt. | VOH | - | 0.8VDD | - | VDD | V |
Output Low Volt. | VOL | - | VSS | - | 0.2VDD | V |
Supply Current(No include LED Backlight) | IDD | VDD=3.3V | - | 1.5 | - | mA |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책