240x128 COG LCD 모듈

모델 번호 WO240128B

►COG LCD
►그래픽 LCD
►240 x 128 점
►IC: ST7586S
►3.3V 전원 공급 장치
►1/128 듀티 사이클
►인터페이스 : 6800/8080/SPI

PDF 다운로드

데모 코드 조회에 추가

이전 목록으로 돌아가기 다음

도면

Chip on Glass LCD Module 240x128 - WO240128B

Data source ref:WO240128B-TFH#

사양

인터페이스 핀 기능

Pin No.

기호

설명

ESD GND

Electro-Static discharge

VG is the power of SEG-drivers

XV0

Negative operating voltage of COM-drivers

Positive operating voltage of COM-drivers

VM is the non-select voltage level of COM-drivers.

VDDA

Power supply

VSS

Ground

VD1

Digital power source selection.

VDDI

VDD1 is the power of interface I/O circuit

CSB

Chip select input pin
CSB=“L”: This chip is selected and the MPU interface is active
CSB=“H”: This chip is not selected and the MPU interface is disabled
(D[7:0] are high impedance)

IF3

These pins select interface operation mode.

IF3	IF2	IF1	MPU interface type
H	H	L	80 series 8-bit parallel
H	L	L	68 series 8-bit parallel
L	H	H	8-bit serial (4-Line)
L	H	L	9-bit serial (3-Line)

IF2

IF1

RSTB

Reset input pin. When RSTB is “L”, internal initialization procedure is executed.

/RD(E)

Read / Write execution control pin. (This pin is only used in parallel interface)

MPU Type	ERD	Descriptin
6800-series	ERD	Read/Write control input pin R/W = "H" When E is "H", data bus is in output status. R/W = "L" The data are lunched at the failling edge of the E signal.
8080-series	/RD	Read enable inputpin. When /RD is "L". Data bus is in output status.

16~23

D7~D0

The bi-directional data bus of the MPU interface. When CSB is “H”, they are high impedance.
If using serial interface:
D0 is the SDA signal in 4-Line & 3-Line interface.
D1 is the A0 signal in 4-Line interface

/WR/(R/W)

Read / Write execution control pin. (This pin is only used in parallel interface

MPU Type	RWR	Descriptin
6800-series	R/W	Read/Write control input pin R/W = "H" : Read R/W = "L" : write
8080-series	/WR	Write enable clock input pin. The data are layched at the rising edge of the /WR signal.

This pin is not used in serial interfaces and should be connected to VDD1

A0(SCL)

The function of this pin is different in parallel and serial interface
In parallel interface: A0 is register selection input
A0 = "H": inputs on data bus are display data
A0 = "L": inputs on data bus are command
In serial interface: this pad will be used as SCL (serial-clock) input

ESD GND

Electro-Static discharge

기계적 데이터

항목	치수	단위
표시 형식	240 x 128	－
모듈 치수	122.2 x 79.8 x 6.5 (MAX)	mm
보기 영역	114.0 x 64.0	mm
활성 영역	107.98 x 57.58	mm
도트 크기	0.43 x 0.43	mm
도트 피치	0.45 x 0.45	mm
듀티	1/128D，1/12B
역광 타입	LED
IC	ST7586S
인터페이스	6800/8080/3-Line/4-Line

절대 최대 정격값

항목	기호	최소값	대표값	최대값	단위
작동 온도	TOP	-20	－	+70	℃
보관 온도	TST	-30	－	+80	℃
Digital Power Supply Voltage	VDDI	-0.3	－	3.6	V
Analog Power supply voltage	VDDA	-0.3	－	3.6	V
LCD Power supply voltage	V0-XV0	-0.3	－	19	V
LCD Power supply voltage	VG	-0.3	－	5.5	V

전기적 특성

항목	기호	조건	최소값	대표값	최대값	단위
Supply Voltage For Logic	VDD-VSS	－	3.0	3.3	3.6	V
Supply Voltage For LCM	VDD-V0	Ta=-20℃ Ta=25℃ Ta=70℃	－ 14.8 －	－ 15.0 －	－ 15.2 －	V V V
Input High Volt.	VIH	－	0.7VDD	－	VDD	V
Input Low Volt.	VIL	－	VSS	－	0.3VDD	V
Output High Volt.	VOH	－	0.8VDD	－	VDD	V
Output Low Volt.	VOL	－	VSS	－	0.2VDD	V
Supply Current(No include LED Backlight)	IDD	VDD=3.3V	－	2.0	4.0	mA

Search keyword: 240x128 lcd, 240 x 128 lcd, lcd 240x128, lcd 240 x 128