ホーム 製品 有機ELディスプレイ キャラクタ 有機EL モジュール WEO001602C

16文字x2行キャラクタ液晶OLED

型番 WEO001602C

►タイプ: キャラクタ表示タイプが (W/O FR)
►結構: COG
►16文字x2行
►SSD1311 コントローラー内蔵
►3V/5V電源電圧
►1/16 duty
►インターフェース: 6800, 8080, SPI, I2C
►発光色: 白色 / 黄色 / 空色 / 緑色
►下の表に利用可能なFPCオプションはあります

製品情報

WINSTARはOLED COG 16x2行 キャラクタOLEDディスプレイの標準品WEO001602C。このモジュールはSSD1311 ICを内蔵して、外形寸法は68.5x17.5mmであります。有機EL・COGモジュールは超薄、軽量、低消費電力のメリットを有して、ハンドヘルド機器、メーター、スマートグリッド、ウェアラブル機器、IoTシステムなどに生かせます。


   FPC Options

 

外形図

Winstar 16x2 OLED Display, Character OLED - WEO001602C

Data source ref: WEO001602CWPP5N00000

製品仕様

ピン功能定義

Pin No. 記号 Pin タイプ 説明
1 NC No connection
2 VSL P This is segment voltage (output low level) reference pin.  
When external VSL is not used, this pin should be left open. 
When external VSL is used, connect with resistor and diode to ground (details depend on application).
3 VSS P Ground pin.  It must be connected to external ground.  
4 REGVDD I Internal VDD regulator selection pin in 5V I/O application mode.  
When this pin is pulled HIGH, internal VDD regulator is enabled (5V I/O application). 
When this pin is pulled LOW, internal VDD regulator is disabled (Low voltage I/O application).  
5 SHLC I This pin is used to determine the Common output scanning direction.
COM scan direction
SHLC COM scan direction
1 COM0 to COM31   (Normal)
0 COM31 to COM0   (Reverse)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
6 SHLS I This pin is used to change the mapping between the display data column address and the Segment driver. 
SEG scan direction
SHLS SEG direction
1 SEG0 to SEG99  (Normal)
0 SEG99 to SEG0  (Reverse)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
7 VDD P Power supply for core logic operation.  
VDD can be supplied externally or regulated internally.   
In LV IO application (internal VDD is disabled), this is a power input pin.
In 5V IO application (internal VDD is enabled), VDD is regulated internally from VDDIO. 
A capacitor should be connected between VDD and VSS under all circumstances.
8 VDDIO P Low voltage power supply and power supply for interface logic level in both Low Voltage I/O and 5V I/O application.  It should match with the MCU interface voltage level and must be connected to external source.
9 BS0 I MCU bus interface selection pins.  Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
Bus Interface selection
BS[2:0] Interface
000 Serial Interface
001 Invalid
010 I2C
011 Invalid
100 8-bit 6800 prallel
101 4-bit 6800 prallel
110 8-bit 8080 prallel
111 4-bit 8080 prallel

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
10 BS1
11 BS2
12 GPIO I/O It is a GPIO pin. Details refer to OLED command DCh.
13 CS# I This pin is the chip select input connecting to the MCU.  
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.  
14 RES# I This pin is reset signal input.  
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
15 D/C# I This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. 
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.   
In I2C mode, this pin acts as SA0 for slave address selection.
When serial interface is selected, this pin must be connected to VSS.
16 R/W#(WR#) I This pin is read / write control input pin connecting to the MCU interface.  
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. 
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E(RD#) I This pin is MCU interface input.  
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.  
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These pins are bi-directional data bus connecting to the MCU data bus. 
Unused pins are recommended to tie LOW.   
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID and D2 will be the serial data output: SOD.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I This pin is the segment output current reference pin.  
IREF is supplied externally.  
A resistor should be connected between this pin and VSS to maintain current of around 15uA.
27 ROM0 I These pins are used to select Character ROM; select appropriate logic setting as described in the following table.  ROM1 and ROM0 are pin select as shown in below table:
Character ROM selection
ROM1 ROM0 ROM
0 0 A
0 1 B
1 0 C
1 1 S/W selectable(3)
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
28 ROM1
29 OPR0 I This pin is used to select the character number of character generator. 
Character RAM selection
OPR1 OPR0 CGROM CGRAM
1 1 256 0
0 1 248 8
1 0 250 6
0 0 240 8
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDDIO
30 OPR1
31 VCOMH P COM signal deselected voltage level.  
A capacitor should be connected between this pin and VSS.  
No external power supply is allowed to connect to this pin. 
32 VCC P Power supply for panel driving voltage.  This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
33 NC No connection

規格説明

項目 サイズ 単位
表示形式 16文字x2行
モジュールサイズ 68.5 x 17.5 x 2.17 mm
表示エリア 58.22 x 13.52 mm
アクティブエリア 56.22 x 11.52 mm
ドットサイズ 0.57 x 0.67 mm
ドットピッチ 0.60 x 0.70 mm
文字サイズ 2.97 x 5.57 mm
文字ピッチ 3.55 x 5.95 mm
パネルタイプ OLED , モノクロ
Duty 1/16
IC SSD1311
インターフェイス 6800, 8080, SPI, I2C
表示サイズ 2.26 インチ

絶対最大定格

項目 記号 最小値 最大値 単位
ロジック電源電圧 VDD -0.3 VDDIO V
入力/出力ピンの電源電圧 VDDIO -0.3 6 V
操作電圧 VCC 0 16 V
操作温度 TOP -40 +80
保存温度 TST -40 +85

電気特性

DC 電気特性

項目 記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VDD Low Voltage I/O 2.4 3.0 3.3 V
5V I/O
(VDD as output)
V
入力/出力ピンの電源電圧 VDDIO Low Voltage I/O 2.4 3.0 3.3 V
5V I/O 4.4 5.0 5.3 V
OLED電源電圧 VCC 8.0 10.0 10.5 V
8.0 12.0 12.5 V
高レベル入力電圧 VIH 0.8xVDDIO V
低レベル入力電圧 VIL 0.2xVDDIO V
高レベル出力電圧 VOH IOH=-0.5mA 0.9xVDDIO V
低レベル出力電圧 VOL IOL=0.5mA 0.1xVDDIO V
50% Check Board Operating Current ICC VCC=10V 16 24 mA
VCC=12V 18 27 mA

FPC Options:

Drawing FPC Length PIN Pitch ZIF FPC or HOTBAR FPC Interface FPC No. Create Date
FPC2070003111XXXXX00_WEO001602CLPP5N00000 35.2 31 0.7 HOTBAR FPC 6800, 8080, SPI, I2C FPC2070003111XXXXX00 20120208
FPC2005003421XXXXX00_WEO001602CWPP3N00F00 31 34 0.5 ZIF FPC 6800, 8080, SPI, I2C FPC2005003421XXXXX00 20161028

Search keyword: oled 16x2, 16x2 oled

go top
close