ホーム 製品 有機ELディスプレイ グラフィック 有機EL モジュール WEO009664B-ZIF

1.1インチ96x64有機ELモジュール - ZIF

型番 WEO009664B-ZIF

►タイプ: グラフィック有機ELモジュール
►結構: COG+ ZIF FPC
►サイズ: 1.1インチ
►96 x 64 ドットマトリックス
►SSD1327コントローラー内蔵
►3V電源電圧
►1/64 duty
►インターフェース: 6800, 8080, SPI, I2C
►発光色: 白色 / 黄色 / グレースケール機能をサポートする

製品情報

WEO009664Bは96x64ピクセルの 1.1インチPM有機ELモジュールです。SSD1327 ICを内臓し、6800/8080 8ビットパラレル、I2C、4線シリアルのインターフェースをサポート致します。供給電圧は 3Vで 、デューティは1/64 で、16 階調グレースケールに対応できます。WEO009664Bは2017年にEOLしたTAB構造の 1.1インチWEX009664A/Bの代替品と見られます。 両方ともAAサイズが近くて、1.1インチ 薄型の有機ELモジュールです。

1.1インチのWEO009664Bは 小サイズのCOG 構造の有機ELモジュールです。 バックライト不要・ 薄くて、ハンドヘルド機器、AI医療機器、パーソナルケア機器 、メーター、AI家電製品、ウェアラブル機器 などに適しております。操作温度範囲は–40℃ to +80℃で、保存温度範囲は –40℃ to +85℃です。

 

外形図

Small OLED Screen, OLED Display Screen, 1.1 OLED Screen Module - WEO009664B

製品仕様

ピン功能定義

No. 記号 説明
1 VSS Ground pin. It must be connected to external ground.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2, BS1 and BS0 are pin select.
Bus Interface selection
 
BS[2:1] Interface
0 4 line SPI
1 I2C
11 8-bit 8080 parallel
10 8-bit 6800 parallel

Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
7 BS2
8 VSS Ground pin. It must be connected to external ground.
9 IREF This pin is the segment output current reference pin
10 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
11 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
12 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
13 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
14 E This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
24 VSS Ground pin.

規格説明

項目 仕様 単位
解像度 96 × 64 Dots
モジュールサイズ 29.00 × 22.50 × 1.65 mm
表示エリア 22.53 × 15.01 mm
ドットサイズ 0.205 × 0.205 mm
ドットピッチ 0.235 × 0.235 mm
表示モード パッシブマトリクス
発光色 モノクロ
駆動方法 1/64 Duty
IC SSD1327
インターフェイス 4-Wire SPI, I2C, 6800, 8080
サイズ 1.1 インチ

電気特性

項目 記号 条件 最小値 典型値 最大値 単位
ロジック電源電圧 VCI 2.8 3.0 3.3 V
Display電源電圧 VCC 8.0 8.5 9.0 V
入力電圧(High) VIH 0.8×VCI VCI V
入力電圧(Low) VIL VSS 0.2×VCI V
出力電圧(High) VOH 0.9×VCI VCI V
出力電圧(Low) VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=8.5V 13.0 26.0 mA

絶対最大定格

パラメーター 記号 最小値 最大値 単位
操作電源電圧 VCI -0.3 4.0 V
ロジック電源電圧 VDD -0.5 2.75 V
Display電源電圧 VCC -0.5 19.0 V
操作温度 TOP -40 +80 °C
保存温度 TSTG -40 +85 °C

Search keyword: 96x64 oled, oled 96x64, 1.1 oled, 1.1" oled, 1.1インチ oled, oled 1.1, oled 1.1"
go top
close