Modello numero WEO025664D
►Tipo : grafico
►Struttura : COG
►Dimensione : 3.55 pollici
►256×64 a matrice di punti
►IC：SSD1322
►Alimentatore 3V
►1/64 duty cycle
►Interfaccia: 6800, 8080, SPI
►Colore display: Bianco / Giallo
►Support Grayscale
WEO025664D è un display OLED grafico COG da 3,55 pollici con risoluzione 256×64 punti. Integra il controller IC SSD1322 e supporta scala di grigi a 4 bit. Sono disponibili interfacce 6800/8080 parallele e SPI a 3/4 fili. L’elevato contrasto e l’ampio angolo di visione garantiscono una buona leggibilità in diverse condizioni di illuminazione.
Il modulo opera con tensione logica di 3,3V e tensione di pilotaggio di 16V. La corrente tipica è 35mA (VCC=16V, pattern checkerboard 50%). Metodo di pilotaggio: 1/64 duty.
Adatto a dispositivi quali apparecchiature medicali, pannelli di controllo, terminali self-service, sistemi di biglietteria e parcometri, dove è richiesto un display OLED monocromatico compatto. Intervallo di temperatura operativa: -40°C ~ +80°C; temperatura di stoccaggio: -40°C ~ +85°C.
| Articolo | Dimensioni | Unità |
|---|---|---|
| A matrice di punti | 256 x 64 | - |
| Dimensione del modulo | 99.2 × 33.5 × 2.01 | mm |
| Area attiva | 87.52 × 21.28 | mm |
| Dimensioni del Dot | 0.312 × 0.303 | mm |
| Passo del Dot | 0.342 × 0.333 | mm |
| Modalità display | Matrice passiva | |
| Colore display | monocromatici | |
| Drive Duty | 1/64 Duty | |
| Scala di grigi | 4 bits | |
| IC | SSD1322 | |
| Interfaccia | 6800, 8080, SPI | |
| Dimensione | 3.55 inch | |
| Parametro | Simbolo | Min | Max | Unità |
|---|---|---|---|---|
| Tensione di alimentazione per la logica | VDD | -0.5 | 2.75 | V |
| Tensione di alimentazione logica | VCI | -0.3 | 4.0 | V |
| Supply Voltage for I/O Pins | VDDIO | -0.5 | VCI | V |
| Tensione di alimentazione display | VCC | -0.5 | 20 | V |
| Temperatura di funzionamento | TOP | -40 | 80 | °C |
| Temperatura di stoccaggio | TSTG | -40 | 85 | °C |
| Parametro | Simbolo | Condizione | Min | Typ | Max | Unità |
|---|---|---|---|---|---|---|
| Tensione di alimentazione logica | VCI | － | 2.4 | 3.3 | 3.5 | V |
| Tensione di alimentazione display | VCC | － | 10.0 | 16.0 | 16.5 | V |
| Logic supply voltage | VDD | － | 2.4 | － | 2.6 | V |
| Power for I/O pins | VDDIO | － | 1.65 | VCI | V | |
| Ingresso livello High | VIH | － | 0.8×VDDIO | － | VDDIO | V |
| Ingresso livello Low | VIL | － | 0 | － | 0.2×VDDIO | V |
| Uscita livello High | VOH | － | 0.9×VDDIO | － | VDDIO | V |
| Uscita livello Low | VOL | － | 0 | － | 0.1×VDDIO | V |
| Display 50% pixel accesi | VCC =16 V | － | - | 35 | 55 | mA |
| Pin Number | Simbolo | I/O | Funzione | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | ESD_GND | P | Ground | ||||||||||
| 2 | VSS | P | Ground. | ||||||||||
| 3 | VCC | P | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. |
||||||||||
| 4 | VCOMH | P | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
||||||||||
| 5 | VLSS | P | Analog system ground pin. | ||||||||||
| 6~13 | D7~D0 | I/O | Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
||||||||||
| 14 | E/RD# | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
| 15 | R/W# | I | Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
||||||||||
| 16 | BS0 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
Note (1) 0 is connected to VSS (2) 1 is connected to VDDIO |
||||||||||
| 17 | BS1 | ||||||||||||
| 18 | D/C# | I | Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
||||||||||
| 19 | CS# | I | Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
||||||||||
| 20 | RES# | I | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
| 21 | FR | O | This pin is No Connection pins. Nothing should be connected to this pin. This pin should be left open individually. | ||||||||||
| 22 | IREF | I | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10uA. |
||||||||||
| 23 | N.C. | - | Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
||||||||||
| 24 | VDDIO | P | Power Supply for I/O Pin It should be matched with the MCU interface voltage level. |
||||||||||
| 25 | VDD | P | Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
||||||||||
| 26 | VCI | P | Power Supply for Operation VCI must always be equal to or higher than VDD and VDDIO. |
||||||||||
| 27 | VSL | P | Voltage Output Low Level for SEG Signal This is segment voltage reference pin. When external VSL is not used, this pin should be left open. When external VSL is used, this pin should connect with resistor and diode to ground. |
||||||||||
| 28 | VLSS | P | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
||||||||||
| 29 | VCC | P | Power Supply for OLED Panel These are the most positive voltage supply pin of the chip. They must be connected to external source. |
||||||||||
| 30 | ESD GND | P | Ground |
Facendo clic su "Consenti tutti i cookie", accetti la memorizzazione dei cookie sul tuo dispositivo per migliorare la navigazione del sito, analizzare l'utilizzo del sito e assistere nei nostri sforzi di marketing e prestazioni. Puoi trovare ulteriori informazioni su questo argomento nella nostra politica. Informativa sulla privacy
