Modello numero WEA012864D-01
►Tipo: grafico
►Struttura: COG+PCB
►Dimensione: 0.96 pollici
►128 x 64 a matrice di punti
►IC：SSD1306
►Alimentatore 3V/5V
►1/64 duty
►Interfaccia: I2C,SPI
►Colore display: Bianco / Giallo / Cielo blu
| No. | Simbolo | Funzione |
|---|---|---|
| 1 | SDA | When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
| 2 | SCL | |
| 3 | SA0 | In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
| 4 | RST | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation. |
| 5 | CS | This pin is the chip select input. (active LOW). |
| 6 | VDD | 3.0V Power supply pin for core logic operation. |
| 7 | VIN | 5.0V Power supply pin for core logic operation. |
| 8 | GND | This is a ground pin. |
| Articolo | Dimensioni | Unità |
|---|---|---|
| A matrice di punti | 128 × 64 | Dots |
| Dimensione del modulo | 38.00 × 28.50 × 2.37 | mm |
| Area attiva | 21.74 × 10.86 | mm |
| Dimensioni del Dot | 0.148 × 0.148 | mm |
| Passo del Dot | 0.17 × 0.17 | mm |
| Modalità display | Matrice passiva | |
| Colore display | Monocromatici | |
| Drive Duty | 1/64 Duty | |
| IC | SSD1306 | |
| Interfaccia | I2C, SPI | |
| Dimensione | 0.96 pollici | |
| Parameter | Simbolo | Valore Min | Valore massimo | Unità |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD | 1.65 | 3.3 | V |
| Supply Voltage for Logic | VIN | 4.0 | 6.0 | V |
| Temperatura di lavoro | TOP | -40 | +80 | °C |
| Temperatura di stock | TSTG | -40 | +85 | °C |
| Articolo | Simbolo | Condizione | Valore Min | Valore tipico | Valore massimo | Unità |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic(3V) | VDD | － | 2.8 | 3.0 | 3.2 | V |
| Supply Voltage for Logic5V) | VIN | － | 4.8 | 5.0 | 5.2 | V |
| Input High Volt. | VIH | － | 0.8×VDD | － | VDDIO | V |
| Input Low Volt. | VIL | － | 0 | － | 0.2×VDD | V |
| Output High Volt. | VOH | － | 0.9×VDD | － | VDDIO | V |
| Output Low Volt. | VOL | － | 0 | － | 0.1×VDD | V |
| 50% Check Board operating Current | ICC | Vcc=7.5V | － | 12.0 | 22.0 | mA |
By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.