1,18 Zoll Rundes OLED Display 128x128
Modellnummer WEO128128B
►1,18 Zoll OLED
►Rundes OLED Display
►Typ: Grafik
►Bauweise: COG
►128x128 Punktmatrix
►IC:SSD1327
►3-V-Stromversorgung
►1/128 duty
►Schnittstelle: 6800, 8080, SPI, I2C
►die Farbe des Displays: Weiß / Gelb
►Unterstützt Grauskala
►Andere in der nachstehenden Tabelle verfügbare FPC-Optionen
Beschreibung
Das Winstar OLED WEO128128B ist ein rundes Passivmatrix-OLED-Display mit einer Auflassung von 128x128 Pixeln und hat einen Durchmesser von 1,18 Zoll. Es eine Modulgröße von 37,18 × 41,23 × 2,05 mm und eine aktive Fläche von Ø30 mm. Es ist mit SSD1327ZB Controller ausgestattet und unterstützt 6800/8080 8-Bit-Parallel-, I2C und 4-Draht-SPI-Seriell-Schnittstelle. Die Versorgungsspannung beträgt 3V. Das Modul ist ein OLED-Display mit COG-Struktur, das extrem dünn ist und keine Hintergrundbeleuchtung benötigt (selbstleuchtend). Es ist leicht und sparsam im Verbrauch. Dieses runde OLED-Modul eignet sich für tragbare Instrumente, Handgeräte, Heimanwendungen usw. Es ist in Weiß, Gelb oder Himmelblau erhältlich.
Das Modul kann bei Temperaturen von -40 ℃ bis +80 ℃ betrieben werden; die Lagertemperatur liegt zwischen -40 ° C und +85 ° C. Im Folgenden finden Sie eine kurze Spezifikation von WEO128128A als Referenz.
FPC-Optionen
Zeichnung
Data source ref: WEO128128BWAP3N00001
Technische Daten
Schnittstelle Pin-Funktion
No. | Symbol | Beschreibung | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
2 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
3 | VCOMH | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin. |
||||||||||
4 | VCI | Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source. VCI must always set to be equivalent to or higher than VDD. |
||||||||||
5 | VDD | Power supply pin for core logic operation. VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated Internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances. |
||||||||||
6 | BS1 |
MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
|
||||||||||
7 | BS2 | |||||||||||
8 | VSS | Ground pin. It must be connected to external ground. | ||||||||||
9 | IREF | This pin is the segment output current reference pin | ||||||||||
10 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
||||||||||
11 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
||||||||||
12 | D/C | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
||||||||||
13 | W/R# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. |
||||||||||
14 | RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
||||||||||
15 | D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
||||||||||
16 | D1 | |||||||||||
17 | D2 | |||||||||||
18 | D3 | |||||||||||
19 | D4 | |||||||||||
20 | D5 | |||||||||||
21 | D6 | |||||||||||
22 | D7 | |||||||||||
23 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source. | ||||||||||
24 | VSS | Ground pin. |
mechanische Daten
Artikel | Ausmaß | Einheit |
---|---|---|
Punktmatrix | 128 x 128 | Punkte |
Abmaße der modul | 37,18× 41,23 × 2,05 | mm |
Aktiver Bereich | Ø30 | mm |
Gray Scale | 4 bits | |
Punktgröße | 0,210 × 0,210 | mm |
Punktabstand | 0,235 × 0,235 | mm |
Display Mode | Passive Matrix | |
Display Color | Monochromes | |
Drive Duty | 1/128 Duty | |
IC | SSD1327 | |
Schnittstelle | 6800, 8080, 4 line SPI, I2C | |
Größe (Diagonale) | 1,18 Zoll |
Absolute Grenzwerte
Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
---|---|---|---|---|
Low voltage power supply, power supply for I/O pins | VCI | -0.3 | 4.0 | V |
Supply Voltage for Logic | VDD | -0.5 | 2.75 | V |
Supply Voltage for Display | VCC | -0.5 | 19.0 | V |
Betriebstemperatur | TOP | -40 | +80 | °C |
Lagertemperatur | TSTG | -40 | +85 | °C |
elektronische Eingenschaften
DC elektronische Eingenschaften
Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
---|---|---|---|---|---|---|
Low voltage power supply, power supply for I/O pins | VCI | Note | 2,8 | 3 | 3,3 | V |
Supply Voltage for Display | VCC | - | 14 | 14,5 | 15 | V |
Supply Voltage for Logic | VDD | - | 2.4 | - | 2.6 | V |
High Level Input | VIH | - | 0,8×VCI | - | VCI | V |
Low Level Input | VIL | - | 0 | - | 0,2×VCI | V |
High Level Output | VOH | - | 0,9×VCI | - | VCI | V |
Low Level Output | VOL | - | 0 | - | 0,1×VCI | V |
50% Check Board operating Current | VCC =14,5V | - | 24 | 26 | mA |
Note: VCI must be larger than or equal to VDD
FPC-Optionen:
Bild | FPC Length | PIN | Pitch | ZIF / HOTBAR FPC | Schnittstelle | FPC No. | Create Date |
---|---|---|---|---|---|---|---|
25.05 | 24 | 0.5 | ZIF | 6800,8080,SPI,I2C | FPC2050002411XXXXX02 | 20160511 | |
91 | 18 | 0.5 | ZIF | 4-line SPI , I2C | FPC2050001811XXXXX04 | 20180705 |