規格圖
Data source ref:WO24064A1-TFH#
產品規格
Pin功能定義
| Pin No. | 符號 | Level | 說明 |
|---|---|---|---|
| 1 | NC | No connection | |
| 2 | FR | O | This is the liquid crystal alternating current signal terminal. |
| 3 | CL | I/O | This is the display clock input terminal The following is true depending on the M/S and CLS status. |
| 4 | /DOF | O | This is the LCD blanking control terminal. |
| 5 | /CS1 | I | This is the chip select signal. When /CS1 = “L” and CS2 = “H”, then the chip Select becomes active, and data/command I/O is enabled. |
| 6 | CS2 | I | |
| 7 | /RES | I | When /RES is set to “L”, the register settings are initialized (cleared). The reset operation is performed by the /RES signal level. |
| 8 | A0 | I | This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command. A0 = “H”: Indicates that D0 to D7 are display data. A0 = “L”: Indicates that D0 to D7 are control data. |
| 9 | /WR | I | When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active. The signals on the data bus are latched at the rising edge of the /WR signal. When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type : When R/W = “H”: Read. When R/W = “L”: Write. |
| 10 | /RD | I | When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active. The data bus is in an output status when this signal is “L”. When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active. This is the enable clock input terminal of the 6800 Series MPU. |
| 11~18 | DB0~DB7 | I/O | Data bus |
| 19 | VDD | P | Power supply |
| 20 | VSS | P | Ground |
| 21 | Vout | O | DC/DC voltage converter. Connect a capacitor between this terminal and VSS or VDD |
| 22 | C3+ | O | DC/DC voltage converter |
| 23 | C1- | ||
| 24 | C1+ | ||
| 25 | C2+ | ||
| 26 | C2- | ||
27 |
V4 | P | This is a multi-level power supply for the liquid crystal drive. The voltage Supply applied is determined by the liquid crystal cell, and is changed through the use of a resistive voltage divided or through changing the impedance using an op. amp. Voltage levels are determined based on Vss, and must maintain the relative magnitudes shown below. V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧Vss |
| 28 | V3 | ||
| 29 | V2 | ||
| 30 | V1 | ||
| 31 | V0 | ||
| 32 | VR | I | Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider. IRS = “L” : the V0 voltage regulator internal resistors are not used. IRS = “H” : the V0 voltage regulator internal resistors are used. |
| 33 | C86 | I | This is the MPU interface selection pin. C86 = “H”: 6800 Series MPU interface. C86 = “L”: 8080 Series MPU interface. |
| 34 | P/S | I | This pin configures the interface to be parallel mode or serial mode. P/S = “H”: Parallel data input/output. P/S = “L”: Serial data input. The following applies depending on the P/S status: P/S Data/Command Data Read/Write Serial Clock “H” A0 D0 to D7 /RD, /WR X “L” A0 SI (D7) Write only SCL (D6) When P/S = “L”, D0 to D5 must be fixed to “H”. /RD (E) and /WR (R/W) are fixed to either “H” or “L”. The serial access mode does NOT support read operation. |
| 35 | NC | No connection | |
| 36 | NC | No connection |
規格說明
| 項目 | 標準尺寸 | 單位 |
|---|---|---|
| 點陣(解析度) | 240 x 64 | － |
| 模組尺寸 | 142.5 x 51.7 x 14.9(MAX) | mm |
| 檢視區域 | 130.2 x 37.6 | mm |
| 有效區域 | 127.17 x 33.89 | mm |
| 點大小 | 0.50 x 0.50 | mm |
| 點間距 | 0.53 x 0.53 | mm |
| 驅動方式 | 1/65 | |
| 背光類型 | LED | |
| IC | ST7565P | |
| 介面 | 6800/8080/4-Line SPI | |
最大絕對額定值
| 項目 | 符號 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|
| 工作溫度 | TOP | -20 | － | +70 | ℃ |
| 儲存溫度 | TST | -30 | － | +80 | ℃ |
| 電源電壓 | VDD | -0.3 | － | 3.6 | V |
| Power supply voltage (VDD standard) | V0,VOUT | -0.3 | － | 14.5 | V |
| Power supply voltage (VDD standard) | V1,V2,V3,V4 | -0.3 | － | V0+0.3 | V |
電氣特性
| 項目 | 符號 | 條件 | 最小值 | 典型值 | 最大值 | 單位 |
|---|---|---|---|---|---|---|
| 邏輯電源電壓 | VDD-VSS | － | 3.0 | 3.3 | 3.6 | V |
| LCM電源電壓 | V0-VSS | Ta=-20℃ Ta=25℃ Ta=70℃ |
－ 10. － |
－ 11.0 － |
－ 11.3 － |
V V V |
| 輸入高電壓 | VIH | － | 0.8 VDD | － | VDD | V |
| 輸入低電壓 | VIL | － | VSS | － | 0.2VDD | V |
| 輸出高電壓 | VOH | － | 0.8VDD | － | VDD | V |
| 輸出低電壓 | VOL | － | VSS | － | 0.2VDD | V |
| 電源電流（不包括LED背光） | IDD | VDD=3.3V | － | 1.5 | 2.5 | mA |
Search Keyword: lcd 240x64, lcd 240 x 64, 240x64 lcd, 240 x 64 lcd
