2.7寸 128x64 COG OLED模块配备PCB和铁框 - WEP012864Q

2.7寸 128x64 COG OLED模块配备PCB和铁框

型号 WEP012864Q

►类型：点阵图形
►结构：COG+铁框+PCB
►尺寸：2.7寸
►128x64点阵
►IC：SSD1309
►3V电源电压
►1/64 duty
►接口：6800，8080，SPI，I2C
►发光颜色: 白色 / 黄色 / 天空蓝 / 绿色

PDF下载

索取Demo Code 产品询问

上一个产品回分类页下一个产品

产品叙述

WEP012864Q系列是一款2.7寸单色绘图型COG OLED显示器模块，分辨率为128x64像素。它内建SSD1309控制器IC，透过6800 8-bit/8080 8-bit并列接口或I2C/4线SPI串行接口进行通信，使用3V电压驱动。 WEP012864Q的模块尺寸为82.0×47.5 mm，有效区域为61.41×30.69 mm。此系列与现有的WEO012864Q和WEF012864Q使用相同的OLED面板。

WEO012864Q 系列特点是无铁框和PCB设计。

WEF012864Q 系列搭配铁框，铁框上设计四个螺丝孔，可增加结构稳定性。

WEP012864Q 系列是同时具有铁框和PCB，PCB上整合有四个螺孔，以便于安装。

这三种不同的结构可满足不同客户的应用需求，为不同的设计考虑和安装偏好提供选项。

如果需要触控功能，请考虑在这个系列中选择 WEP012864Q-CTP 型号。

OLED COG显示器模块因为非常的薄，重量轻巧且低耗电流并具有10,000:1的高对比度度，所以非常适合手持式产品、量测仪器、智能电表、穿戴式产品、物联网设备等。WEP012864Q OLED模块可在-40℃至+80℃的温度下工作；其储存温度范围为-40℃至+80℃。

规格图

2.7-inch 128x64 COG OLED Display with PCB and Frame - WEP012864Q

Data source ref: WEP012864QLPP3N00000

产品规格

Pin功能定义

No.

符号

功能说明

VSS

Ground.

VDD

Power supply pin for core logic operation

No connection

D/C#

This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.

R/W#
(WR#)

This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

E(/RD#)

This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.

7-14

D0~D7

These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.

No connection

RES#

This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.

CS#

This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

No connection

BS2

MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select

	BS1	BS2
I2C	1	0
4-wire Serial	0	0
8-bit 68XX Parallel	0	1
8-bit 80XX Parallel	1	1

Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD

BS1

No connection

规格说明

项目	尺寸	单位
点阵(分辨率)	128 × 64	dots
模块尺寸	82.0 × 47.5 × 7 Max.	mm
视域尺寸	61.41 × 30.69	mm
点大小	0.45 × 0.45	mm
点间距	0.48 × 0.48	mm
显示模式	被动矩阵
发光颜色	单色
驱动方式	1/64 Duty
IC	SSD1309
介面	I2C, 4-Wire SPI ,6800, 8080
尺寸	2.7 寸

最大绝对额定值

参数	符号	最小值	最大值	单位
逻辑电源电压	VDD	-0.3	4.0	V
工作温度	TOP	-40	+80	°C
储存温度	TSTG	-40	+85	°C

电气特性

项目	符号	条件	最大值	典型值	最大值	单位
逻辑电源电压	VDD	－	2.8	3.0	3.3	V
输入高准位	VIH	－	0.8×VDD	－	－	V
输入低准位	VIL	－	－	－	0.2×VDD	V
输出高准位	VOH	－	0.9×VDD	－	－	V
输出低准位	VOL	－	－	－	0.1×VDD	V
50%显示画面耗电流		VCC =3V	-	100	200	mA