제품 TFT LCD IPS 패널, IPS 디스플레이 WF28JSYAJDNN0

2.8 인치 240x320 햇빛 읽기 쉬운 IPS TFT

모델 번호 WF28JSYAJDNN0

►크기 : 2.8 인치
►디스플레이 형식 : 240 x 320 dots
►뷰 방향 : IPS
►인터페이스 : MCU, SPI
►TFT 드라이버 IC: ILI9341V
►제어 보드 : 없음
►밝기(cd/m²): 1000
►스루 홀 프레임 : 없음
►터치스크린 : 없음

설명

 

도면

2.8 inch 240x320 Sunlight Readable TFT IPS LCD - WF28JSYAJDNN0 - Winstar Display

사양

인터페이스 핀 기능

LCM PIN Definition

NO 기호 기능 I/O
1 GND Ground P
2-6 NC No connection -
7 VCI High voltage power supply for analog circuit blocks
(2.5 ~ 3.3 V)
P
8 IOVCC Low voltage power supply for interface logic circuits
(1.65 ~ 3.3 V)
P
9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
If not used, open this pin.
O
10 CS Chip select signal. I
11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
When DCX = 1, data is selected.
When DCX = 0, command is selected.
(SCL): This pin is used as the serial interface clock in 3-wire
9-bit/4-wire 8-bit serial data interface.
If not used, this pin should be connected to VDDI or VSS.
I
12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
(D/CX) - 4-line system: Serves as the selector of command or parameter.
Fix to VDDI level when not in use.
I
13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
Fix to VDDI level when not in use.
I
14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB
interface mode
Fix to VSS level when not in use.
I/O
30 RESET This signal will reset the device and must be applied to properly initialize the chip.
Signal is active low.
I
31 IM0 Select the MCU interface mode
IM2 IM1 1M0 MCU-Interface Mode DB Pin in use
Register/Content GRAM
0 0 0 80 MCU 8-bit bus interface I D[7:0] D[7:0]
0 0 1 80 MCU 16-bit bus interface I D[7:0] D[15:0]
0 1 0 80 MCU 9-bit bus interface I D[7:0] D[8:0]
0 1 1 80 MCU 18-bit bus interface I D[7:0] D[17:0]
1 0 1 3-wire 9-bit data serial interface I SDA: In/Out
1 1 0 4-wire 8-bit data serial interface I SDA: In/Out
MPU Parallel interface bus and serial interface select
If use RGB Interface must select serial interface.
* : Fix this pin at VDDI or VSS.
I
32 IM1
33 IM2
34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB
interface mode
Fix to VSS level when not in use.
I/O
35 DB17
36 LEDK Cathode of LED backlight. P
37 LEDK Cathode of LED backlight. P
38 LEDA Anode of LED backlight. P
39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
When IM[3] : High, Serial input signal.
The data is applied on the rising edge of the SCL signal.
If not used, fix this pin at VDDI or VSS.
I/O
40 SDO Serial output signal.
The data is outputted on the falling edge of the SCL signal.
If not used, open this pin
O

일반 사양

항목 치수 단위
크기 (대각선) 2.8 인치
도트 매트릭스 (해상도) 240 x RGB x 320(TFT) dots
모듈 치수 50.5(W) x 69.7(H) x 4.55(D) mm
활성 영역 43.2 x 57.6 mm
도트 피치 0.18 x 0.18 mm
LCD 유형 TFT, 검은색, 투과성
TFT 드라이버 IC ILI9341V 또는 이와 동등한
TFT 인터페이스 MCU/SPI
시야각 80/80/80/80
종횡비 3:4
역광 타입 LED,백색
터치 패널 터치패널(스크린)이 없는
표면 눈부심

절대 최대 정격값

항목 기호 최소값 대표값 최대값 단위
작동 온도 TOP -20 +70
보관 온도 TST -30 +80

전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage for digital IOVCC 1.65 3.3 V
Supply Voltage for analog VCI 2.5 3.3 V
Power Supply for Current ICC IOVCC=VCI
=VCC=3.28V
12 18 mA
go top
close