Accueil Produits Écran OLED Afficheur OLED Graphique WEO012864AG

Module d'affichage OLED monochrome 0,96 pouce avec une résolution de 128x64

N° de modèle WEO012864AG

►Type: Graphique
►Structure: COG
►Dimension: 0.96 pouces
►Matrice de points 128 x 64
►IC:SSD1315
►Alimentation 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Couleur d'affichage: Blanc

Description

Le WEO012864AG est un module d'affichage OLED monocouche à matrice passive doté d'une structure COG (Chip-on-Glass) graphique et d'une diagonale de 0,96 pouces, offrant une résolution de 128x64 points et un rapport de contraste élevé de 10000:1. Il fonctionne avec une alimentation électrique logique de 3V, avec un cycle de service de 1/64. Ce monochrome OLED de la série WEO012864AG est équipé du circuit intégré SSD1315, offrant la prise en charge des interfaces 8-bit 6800/8080, I2C et SPI à 3 fils/4 fils, ainsi que des options d'amplification de puissance interne et d'alimentation externe.

Ce module OLED fonctionne de manière fiable dans une plage de température de -30°C à +70°C, avec une température de stockage de -30°C à +70°C. Il est conçu pour être polyvalent et trouve une excellente utilité dans les équipements médicaux tels que les oxymètres, ainsi que dans divers instruments de mesure tels que le détecteur de puissance USB, le rapporteur d'angle numérique, etc.

Module d'affichage OLED monochrome 0,96 pouce avec une résolution de 128x64 - WEO012864AG

DESSIN

128x64 0.96 inch Monochorme OLED Display Module - WEO012864AG
Data source ref:WEO012864AGWPP3N0Y000

SPÉCIFICATIONS

Fonction PIN sur l'interface

Pin No. Symbole Fonction
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2P C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2N
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
7 NC NC
8 VSS This is a ground pin.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
No. BS0 BS1 BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX parallel 0 0 1
8-bit 8080 parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
When internal IREF is used, this pin should be kept NC.
27 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

Données mécaniques

Article Dimensions Unité
Matrice de points 128 x 64
Dimensions du module 24.7 x 16.59 x 1.41 mm
Zone active 21.74 x 11.18 mm
Taille des points 0.15 x 0.155 mm
Pas des points 0.17 x 0.175 mm
Mode d'affichage Passive Matrix
Couleur d'affichage MonoChrome
Duty 1/64 Duty
IC SSD1315
Interface 6800,8080,SPI,I2C
Diagonale 0.96 pouces

Valeurs nominales maximales absolues

Parameter Symbole Min Max Unité
Supply Voltage For Logic VDD 0 4 V
Charge Pump Regulator Supply Voltage VBAT -0.3 6.0 V
Supply Voltage for Display VCC 0 18.0 V
Température de fonctionnement TOP -30 +70
Température de stockage TSTG -30 +70

Caractéristiques électroniques

Article Symbole État Min Typ Max Unité
Supply Voltage For Logic VDD 1.65 3.0 3.3 V
Supply Voltage for Display(Supplied Externally) VCC 7.5 8.0 V
Charge Pump Regulator Supply Voltage VBAT 3.0 3.5 4.5 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump VCC 7.0 7.5 V
Input High Volt. VIH 0.8xVDD V
Input Low Volt. VIL 0.2VDD V
Output High Volt. VOH 0.9xVDD V
Output Low Volt. VOL 0.1xVDD V
Operating Current for VCC
(Display 50% Pixel on)(VCC Supplied Externally)
ICC VCC=7.5V 5.0 10 mA
Display 50% Pixel on
(VCC Generated by Internal DC/DC)
IBAT VBAT=3.5V 15 22.5 mA


Search keyword: 128x64 lcd, 128 x 64 lcd, lcd 128x64, lcd 128 x 64

go top
close

We value your privacy

By clicking "Allow All Cookies", you agree to the storing of cookies on your device to enhance site navigation, analyse site usage, and assist in our marketing and performance efforts. You can find further information this subject in our policy.

We value your privacy

Winstar and certain third parties use cookies on www.winstar.com.tw. The details regarding the types of
cookies, their purpose and the third parties involved are described below and in our Cookie Policy.
Please click on “Allow All” to consent to our usage of cookies in order to have the best possible
experience on our websites. You can also set your preferences or reject cookies (except for strictly
necessary cookies).

Manage Consent Preferences

Always Active
Essential Cookies

These cookies are essential in order to enable you to move around the website and use its
features, such as setting your privacy preferences, logging in or filling in forms. See
Detail.

Analytics Cookies

Also known as “statistics cookies,” these cookies collect information about how you use a website, like which pages you visited and which links you clicked on. See Detail