128x64 Pixeln Grafik-OLED-Module 0,96 Zoll
Modellnummer WEO012864C
►Typ: Grafik
►Bauweise: COG
►Größe: 0,96 Zoll
►128 x 64 Punktmatrix OLED
►IC：SH1106
►3-V-Stromversorgung
►1/64 duty
►Schnittstelle: 6800, 8080, SPI, I2C
►die Farbe des Displays: Weiß / Gelb
►Andere in der nachstehenden Tabelle verfügbare FPC-Optionen
Beschreibung
Das WEO012864C ist ein kleines OLED-Display mit einer Auflösung von 128x64 Pixeln. Die Diagonale beträgt nur 0,96 Zoll. Das Display hat eine Abmessung von 26,70 x 19,26 mm und eine AA-Größe von 21,74 x 10,86 mm. Es ist mit SH1106 Controller ausgestattet und verfügt über 6800/8080 8-Bit Parallel-, I2C und 4-Draht-Seriell-Schnittstellen. Das WEO012864C ist ein kleines COG-OLED-Display, das sehr dünn und leicht ist und geringer Stromverbrauch benötigt. Es ist geeignet für Handgeräte, Messgeräte, MP3, tragbare Geräte, IoT etc. Das Modul kann bei Temperaturen von -40 ℃ bis + 80 ℃ betrieben werden; die Lagertemperatur liegt zwischen -40 ° C und + 85 ° C.
FPC-Optionen Zeichnung
WEO012864C with Hotbar FPC
Data source ref: WEO012864CWAP3N00001
WEO012864C with ZIF FPC
Technische Daten
Schnittstelle Pin-Funktion
| No. | Symbol | Funktion | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | NC | No connection | |||||||||||||||
| 2 | C1N | Connect to charge pump capacitor. These pins are not used and should be disconnected when Vpp is supplied externally. |
|||||||||||||||
| 3 | C1P | ||||||||||||||||
| 4 | C2P | Connect to charge pump capacitor. These pins are not used and should be disconnected when Vpp is supplied externally. |
|||||||||||||||
| 5 | C2N | ||||||||||||||||
| 6 | VDD2 | 3.0 – 4.7V power supply pad for Power supply for charge pump circuit. This pin should be disconnected when VPP is supplied externally |
|||||||||||||||
| 7 | NC | No connection | |||||||||||||||
| 8 | VSS | Ground. | |||||||||||||||
| 9 | VDD1 | Power supply input: 1,65 - 3,5V | |||||||||||||||
| 10 | NC | No connection | |||||||||||||||
| 11 | IM1 | These are the MPU interface mode select pads.
|
|||||||||||||||
| 12 | IM2 | ||||||||||||||||
| 13 | CSB | This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled. | |||||||||||||||
| 14 | RESB | This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level. | |||||||||||||||
| 15 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers. In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver. |
|||||||||||||||
| 16 | WRB | This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When R/W = “H”: Read. When R/W = “L”: Write. |
|||||||||||||||
| 17 | RDB | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU. When RD = “H”: Enable. When RD = “L”: Disable. |
|||||||||||||||
| 18 | D0 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance. When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance. |
|||||||||||||||
| 19 | D1 | ||||||||||||||||
| 20 | D2 | ||||||||||||||||
| 21 | D3 | ||||||||||||||||
| 22 | D4 | ||||||||||||||||
| 23 | D5 | ||||||||||||||||
| 24 | D6 | ||||||||||||||||
| 25 | D7 | ||||||||||||||||
| 26 | IREF | This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA. | |||||||||||||||
| 27 | VCOMH | This is a pad for the voltage output high level for common signals. A capacitor should be connected between this pad and VSS. |
|||||||||||||||
| 28 | VPP | OLED panel power supply. Generated by internal charge pump. Connect to capacitor. It could be supplied externally. |
|||||||||||||||
| 29 | NC | No connection | |||||||||||||||
| 30 | NC | No connection |
Allgemeine Spezifikationen
| Artikel | Ausmaß | Einheit |
|---|---|---|
| Punktmatrix | 128 x 64 | － |
| Abmaße der modul | 26,70 × 19,26 × 1,26 | mm |
| Aktiver Bereich | 21,74 × 10,86 | mm |
| Pixelgröße | 0,148 × 0,148 | mm |
| Pixelabstand | 0,170 × 0,170 | mm |
| der Anzeigemodus | Passive Matrix | |
| die Farbe des Displays | Monochrome | |
| Drive Duty | 1/64 Duty | |
| Controller IC | SH1106 | |
| Schnittstelle | 6800, 8080, SPI, I2C | |
| Größe | 0,96 Zoll | |
Absolute Grenzwerte
| Parameter | Symbol | Mindestwert | Maximalwert | Einheit |
|---|---|---|---|---|
| Supply Voltage for Logic | VDD1 | -0,3 | 3,6 | V |
| Power supply for charge pump circuit | VDD2 | -0,3 | 4,8 | V |
| Supply Voltage for Display | VPP | -0,3 | 14,5 | V |
| Betriebstemperatur | TOP | -40 | +80 | °C |
| Lagertemperatur | TSTG | -40 | +85 | °C |
Elektronische Eingenschaften
DC Elektronische Eingenschaften
| Artikel | Symbol | Bedingung | Mindestwert | typischer Wert | Maximalwert | Einheit |
|---|---|---|---|---|---|---|
| Supply Voltage for Logic | VDD1 | － | 2,8 | 3,0 | 3,3 | V |
| Power supply for charge pump circuit | VDD2 | － | 3,5 | 3,8 | 4,2 | V |
| Charge Pump Output Voltage for Display (Generated by Internal DC/DC) |
Charge Pump VPP |
－ | 7,5 | 8 | 8,5 | V |
| High Level Input | VIH | － | 0,8xVDD1 | － | VDD1 | V |
| Low Level Input | VIL | － | VSS | － | 0,2xVDD1 | V |
| High Level Output | VOH | － | 0,8xVDD1 | － | VDD1 | V |
| Low Level Output | VOL | － | VSS | － | 0,2xVDD1 | V |
| Operating Current for VDD2 Display 50% ON | IDD2 | － | － | 10 | 16 | mA |
FPC-Optionen:
| Bild | FPC Length | PIN | Pitch | ZIF FPC or HOTBAR FPC | Schnittstelle | FPC No. | Create Date |
|---|---|---|---|---|---|---|---|
 |
13 | 30 | 0.7 | HOTBAR FPC | 6800, 8080, 4-Wire SPI, I2C | FPC2070003001XXXXX09 | 20180613 |
 |
40.95 | 30 | 0.5 | ZIF | 6800, 8080, SPI, I2C | FPC2050003011XXXXX23 | 20190412 |
