产品叙述
WEO009632B Hotbar版本是一款小型OLED显示器模块,分辨率为96x32像素,尺寸为0.68寸。模块内置SSD1305驱动器IC; 此模块支持8-bit 6800/8080 并列式接口、I2C和4线SPI接口。WEO009632B-Hotbar版本电源电压为3V,驱动为1/32 duty; 50%显示画面耗电为6mA@12Vcc (典型值)。OLED显示器具有超薄、重量轻、低功耗且无需背光等特性。适用于手提式设备、个人护理设备、健康器材、仪表设备…等。WEO009632B-Hotbar模块工作温度为-40℃至+80℃;储存温度为-40℃至+85℃。
规格图

Data source ref: WEO009632BWPP3N00H00
产品规格
Pin功能定义
Pin No. | 符号 | I/O | 功能 | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | N.C. | - | Reserved Pin(Supporting Pin) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. |
|||||||||||||||
2,23 | VSS | P | Ground of Logic Circuit This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground. |
|||||||||||||||
3,24 | VCC | P | Power Supply for OLED Panel This is the most positive voltage supply pin of the chip. It must be supplied externally. |
|||||||||||||||
4 | VCOMH | O | Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. |
|||||||||||||||
5 | IREF | I | Current Reference for Brightness Adjustment This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10μA. |
|||||||||||||||
6 | D0~D7 | I/O | Host Data In put/ Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2Cmode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL. |
|||||||||||||||
7 | ||||||||||||||||||
8 | ||||||||||||||||||
9 | ||||||||||||||||||
10 | ||||||||||||||||||
11 | ||||||||||||||||||
12 | ||||||||||||||||||
13 | ||||||||||||||||||
14 | E(RD#) | I | Read/Write Enable or Read This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. |
|||||||||||||||
15 | R/W# (WR#) |
I | Read/ Write Selector Write This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XXinterface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. |
|||||||||||||||
16 | D/C# | I | Data/ Command Control This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data. When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams. When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. |
|||||||||||||||
17 | RES# | I | Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed. |
|||||||||||||||
18 | CS# | I | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
|||||||||||||||
19 | BS2 | I | Communicating Protocol Select These pins are MCU interface selection input. See the following table:
(1) 0 is connected to VSS (2) 1 is connected to VDDIO |
|||||||||||||||
20 | BS1 | I | ||||||||||||||||
21 | VDDIO | P | Power supply for interface logic level. It should be match with MCU interface voltage level. VDDIO must always be equal or lower than VDD. |
|||||||||||||||
22 | VDD | P | Power Supply for Logic Circuit This is a voltage supply pin. It must be connected to external source. |
|||||||||||||||
25 | N.C. | - | Reserved Pin(Supporting Pin) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. |
规格说明
项目 | 规格 | 单位 |
---|---|---|
分辨率 | 96 × 32 | Dots |
模块尺寸 | 19.80 × 12.32 × 1.21 (mm) | mm |
有效区域 | 16.298 × 5.418 (mm) | mm |
像素大小 | 0.148 × 0.148 (mm) | mm |
像素间距 | 0.17 × 0.17 (mm) | mm |
显示模式 | 被动矩阵 | |
发光颜色 | 单色 | |
驱动方式 | 1/32 Duty | |
IC | SSD1305 | |
接口 | 6800, 8080, SPI, I2C | |
尺寸 | 0.68 寸 |
最大绝对额定值
参数 | 符号 | 最小值 | 最大值 | 单位 |
---|---|---|---|---|
逻辑电源电压 | VDD | -0.3 | 4 | V |
显示电源电压 | VCC | 0 | 16 | V |
工作温度 | TOP | -40 | +80 | °C |
储存温度 | TSTG | -40 | +85 | °C |
电气特性
DC特性
项目 | 符号 | 条件 | 最小值 | 典型值 | 最大值 | 单位 |
---|---|---|---|---|---|---|
逻辑电源电压 | VDD | - | 2.8 | 3.0 | 3.3 | V |
显示电源电压 | VCC | - | 11.5 | 12 | 12.5 | V |
输入高准位 | VIH | - | 0.8×VDD | - | VDD | V |
输入低准位 | VIL | - | 0 | - | 0.2×VDD | V |
输出高准位 | VOH | Iout = 100uA | 0.9×VDD | - | VDD | V |
输出低准位 | VOL | Iout = 100uA | 0 | - | 0.1×VDD | V |
符号 | 参数 | 最小值 | 典型值 | 最大值 | 单位 | 条件 |
---|---|---|---|---|---|---|
ICC | VCC Supply Current | - | 6 | 9 | mA | VDD =3.0V , Display 100% ON |
FPC options
Drawing | FPC Length | PIN | pitch | ZIF FPC or HOTBAR FPC | Interface | FPC No. | Create Date |
---|---|---|---|---|---|---|---|
![]() |
30 | 28 | 0.5 | ZIF FPC | 6800, 8080,4-Wire SPI, I2C | FPC2050002811XXXXX01 | 20180131 |
![]() |
8.479 | 25 | 0.65 | HOTBAR FPC | 6800, 8080,4-Wire SPI, I2C | FPC2065002501XXXXX00 | 20190906 |
Search keyword: 96x32 oled, oled 96x32, 0.68 oled, 0.68" oled, 0.68寸 oled, oled 0.68"