Home Produtos Display OLED Display OLED Gráfico WEO012864AA

Display OLED SSD1327, 128x64, 1,54 polegadas

Model No. WEO012864AA

►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 1,54 polegadas
►Matriz de pontos 128 x 64
►IC:SSD1327
►Alimentação 3V
►1/64 duty
►Interface: 6800,8080,SPI,I2C
►Display Color: Branco / Amarelo
►Suporte em escala de cinza

Descrição

WEO012864AA é um display OLED gráfico com IC SSD1327 é fabricado com 128 x 64 pontos de cor monocromática individual, tamanho diagonal de 1,54 polegadas, 1/64 Duty. Este módulo tem dimensão de módulo de 42,04 x 27,22 mm e área ativa de 35,05 x 17,51 mm.

Este display OLED COG está integrado com o IC SSD1327 que tem diferentes interfaces opcionais; ele suporta interface paralela de 6800/ 8080 e interface serial I2C, SPI de 4 fios. Ele tem alto relação de contraste com de 10,000:1 (valor típico). Esta série de módulos pode operar a temperaturas de -40℃ a +80℃; suas temperaturas de armazenamento variam de -40℃ a +85℃.

DRAWING

1.54 OLED SSD1327 Display, 128x64 COG SSD1327 OLED Support Grayscale - WEO012864AA

Data source ref:WEO012864AAWAP3N00000

SPECIFICATIONS

Função do pino de interface

Pin No. Símbolo Descrição
1 VSS This is a ground pin.
2 VCC Power supply for panel driving voltage.
3 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS. No external power supply is allowed to connect to this pin.
4 VCI Low voltage power supply and power supply for interface logic level. It should match with the MCU interface voltage level and must be connected to external source.
VCI must always set to be equivalent to or higher than VDD.
5 VDD Power supply pin for core logic operation.
VDD can be supplied externally (within the range of 2.4V to 2.6V) or regulated internally from VCI. A capacitor should be connected between VDD and VSS under all circumstances.
6 BS1 Communicating Protocol Select
These pins are MCU interface selection input. See the following table:
  68XX-parallel 80XX-parallel Serial I2C
BS1 0 1 0 1
BS2 1 1 0 0
7 BS2
8 VSS This is a ground pin.
9 IREF This pin is the segment output current reference pin.
A resistor should be connected between this pin and VSS to maintain the current around 10uA.
10 CS# This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
11 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. 
12 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
13 R/W# (WR#) This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
14 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
15 D0 These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK.
16 D1
17 D2
18 D3
19 D4
20 D5
21 D6
22 D7
23 VCC Power supply for panel driving voltage.
24 VSS This is a ground pin.

Dados Mecânicos

Item Dimensão Unidade
Matriz de pontos 128 × 64 ponto
Dimensão do módulo 42.04 × 27.22 × 1.41 mm
Área ativa 35.05 × 17.51 mm
Tamanho do ponto 0.249 × 0.249 mm
Distância entre pontos 0.274 × 0.274 mm
Modo de exibição Passive Matrix
Cor de exibição Monochrome
Drive Duty 1/64 Duty
IC SSD1327
Interface 6800/8080/4-Wire SPI/I2C
Tamanho 1,54 polegadas

Classificações Máximas Absolutas

Parameter Símbolo Valor Min Valor Máximo Unidade
Low voltage power supply, power supply for I/O pins VCI -0.3 4.0 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for Display VCC -0.5 19.0 V
Temperatura de operação TOP -40 +80 °C
Temperatura de armazenamento TSTG -40 +85 °C

Características Eletrônicas

DC Características Eletrônicas

Item Símbolo Condição Valor Min Valor Típico Valor Máximo Unidade
Low voltage power supply, power supply for I/O pins VCI 1.65 3.0 3.5 V
Supply Voltage for Display VCC 8.0 12.5 13.0 V
Supply Voltage for Logic VDD 1.65 2.6 V
High Level Input VIH 0.8×VCI VCI V
Low Level Input VIL 0 0.2×VCI V
High Level Output VOH 0.9×VCI VCI V
Low Level Output VOL 0 0.1×VCI V
50% Check Board operating Current ICC VCC =12.5V 10 20 mA
go top
close