Display OLED Gráfico 128x64 de 2,7 polegadas
Model No. WEO012864U
►Tipo: Gráfico
►Estrutura: COG
►Tamanho: 2,7 polegadas
►Matriz de pontos 128 x 64
►IC:SSD1357
►Alimentação 3V
►1/64 duty
►Interface: 6800, 8080, SPI, I2C
►Display Color: Branco / Amarelo
►Support Grayscale
Descrição
O WEO012864U é um popular display OLED gráfico de 2,7 polegadas com uma estrutura COG e uma resolução de 128x64 pontos. Este módulo é construído com o circuito integrado SSD1357, suportando interfaces paralelas de 6800/8080 de 8 bits, I2C e SPI de 4 fios, com uma tensão de alimentação para a lógica de 3V e um ciclo de serviço de 1/64.
O módulo OLED WEO012864U possui uma alta taxa de contraste de 10.000:1 e suporta imagens em escala de cinza de 4 bits. É ideal para dispositivos de parede/medidores, aplicações residenciais, POS financeiros, sistemas Cloud/IoT, dispositivos de tecnologia inteligente, sistemas de energia, sistemas de comunicação, instrumentos médicos, etc. O módulo WEO012864U pode operar em temperaturas que variam de -40°C a 80°C, com temperaturas de armazenamento variando de -40°C a 85°C.
Painéis OLED semelhantes também estão disponíveis na série WEF012864U, que inclui uma estrutura de metal, mas exclui uma placa de circuito (PCB), e na série WEP012864U, que apresenta tanto uma estrutura de metal quanto uma PCB. Se a funcionalidade de toque for necessária, considere optar pela série WEP012864U-CTP.
DRAWING
Data source ref:WEO012864UWPP3N00000
SPECIFICATIONS
Função do pino de interface
No. | Símbolo | Função | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | NC(GND) | No connection. | |||||||||||||||
2 | VSS | Ground of Logic Circuit. This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground. |
|||||||||||||||
3 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin. | |||||||||||||||
4 | VCOMH | Voltage Output High Level for COM Signal. This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS. |
|||||||||||||||
5 | VLSS | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
|||||||||||||||
6~13 | D7~D0 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
|||||||||||||||
14 | E/RD# | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled HIGH and the chip is selected. When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
15 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
|||||||||||||||
16 17 |
BS1 BS2 |
Communicating Protocol Select. These pins are MCU interface selection input. See the following table:
|
|||||||||||||||
18 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
|||||||||||||||
19 | CS# | Chip Select This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. |
|||||||||||||||
20 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
|||||||||||||||
21 | FR | Frame Frequency Triggering Signal This pin will send out a signal that could be used to identify the driver status. Nothing should be connected to this pin. It should be left open individually. |
|||||||||||||||
22 | IREF | This pin is the segment output current reference pin. IREF is supplied externally. |
|||||||||||||||
23 | N.C. | Reserved Pin The N.C. pin between function pins is reserved for compatible and flexible design. |
|||||||||||||||
24 | VDD | Power Supply for I/O Pin. This pin is a power supply pin of I/O buffer. It should be connected to VCI or external source. All I/O signal should have VIH reference to VDDIO. When I/O signal pins (BS0~BS1, D0~D7, control signals…) pull high, they should be connected to VDDIO. |
|||||||||||||||
25 | VP | Power Supply for Core Logic Circuit This is a voltage supply pin. It can be supplied externally (within the range of 2.4~2.6V) or regulated internally from VCI. A capacitor should be connected between this pin & VSS under all circumstances. |
|||||||||||||||
26 | VDD | Power Supply for Operation. This is a voltage supply pin. It must be connected to external source & always be equal to or higher than VDD & VDDIO. |
|||||||||||||||
27 | VSL | Voltage Output Low Level for SEG Signal This is segment voltage (output low level) reference pin. This pin has to connect with resistor and diode to ground (details depends on application). |
|||||||||||||||
28 | VLSS | Ground of Analog Circuit These are the analog ground pins. They should be connected to VSS externally. |
|||||||||||||||
29 | VCC | Power Supply for OEL Panel These are the most positive voltage supply pin of the chip. They must be connected to external source. |
|||||||||||||||
30 | NC(GND) | No connection |
Dados Mecânicos
Item | Dimensão | Unidade |
---|---|---|
Matriz de pontos | 128 x 64 | Pontos |
Dimensão do módulo | 73.0 × 41.86 × 2.01 | mm |
Área ativa | 61.41 × 30.69 | mm |
Tamanho do ponto | 0.45 × 0.45 | mm |
Distância entre pontos | 0.48 × 0.48 | mm |
Modo de exibição | Passive Matrix | |
Cor de exibição | Monochrome | |
Drive Duty | 1/64 Duty | |
IC | SSD1357 | |
Interface | 6800, 8080, SPI, I2C | |
Tamanho | 2,7 polegadas |
Classificações Máximas Absolutas
Parameter | Símbolo | Valor Min | Valor Máximo | Unidade |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4.0 | V |
Supply Voltage for Display | VCC | 0 | 15.0 | V |
Temperatura de operação | TOP | -40 | 80 | °C |
Temperatura de armazenamento | TSTG | -40 | 85 | °C |
Características Eletrônicas
Item | Símbolo | Condição | Valor Min | Valor Típico | Valor Máximo | Unidade |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
Supply Voltage for Display | VCC | - | 9.5 | 10.0 | 10.5 | V |
High Level Input | VIH | - | 0.8×VDD | - | - | V |
Low Level Input | VIL | - | - | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | - | V |
Low Level Output | VOL | - | - | - | 0.1×VDD | V |
50% Check Board operating Current | VCC =10.0V | - | 46 | 69 | mA |