우리는 귀하의 프라이버시를 소중히 여깁니다
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책
Data source ref:WEP012864AJLPP3N00000
항목 | 치수 | 단위 |
---|---|---|
도트 매트릭스 | 128 x 64 | - |
모듈 치수 | 75.0 × 52.7 × 8.5(Max). | mm |
활성 영역 | 55.01 × 27.49 | mm |
도트 크기 | 0.40 × 0.40 | mm |
도트 피치 | 0.43 × 0.43 | mm |
디스플레이 모드 | 패시브 매트릭스 | |
디스플레이 색상 | Monochrome | |
드라이브 듀티 | 1/64 Duty | |
IC | CH1116 | |
인터페이스 | 8080 | |
크기 | 2.42 인치 |
Parameter | 기호 | 최소값 | 최대값 | 단위 |
---|---|---|---|---|
로직 공급 전압 | VDD | -0.3 | 3.6 | V |
작동 온도 | TOP | -40 | +80 | °C |
보관 온도 | TSTG | -40 | +85 | °C |
항목 | 기호 | 조건 | 최소값 | 대표값 | 최대값 | 단위 |
---|---|---|---|---|---|---|
로직 공급 전압 | VDD | - | 2.8 | 3.0 | 3.3 | V |
높은 수준의 입력 | VIH | - | 0.8×VDD | - | VDD | V |
낮은 수준의 입력 | VIL | - | VSS | - | 0.2×VDD | V |
높은 수준의 출력 | VOH | - | 0.8×VDD | - | VDD | V |
저수준 출력 | VOL | - | VSS | - | 0.2×VDD | V |
50% 픽셀 표시 | IDD | VDD =3.0V | - | 60 | 120 | mA |
No. | 기호 | 기능 |
---|---|---|
1 | VDD | Power supply input |
2 | VSS | Ground. |
3 | NC | No connection |
4~11 | D0~D7 | This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus. |
12 | CS# | This pad is the chip select input. When="L", then the chip select becomes active, and data/command I/O is enabled. |
13 | NC | No Connection |
14 | RES# | This is a reset signal input pad. When is set to "L", the settings are initialized. The reset operation is performed by the signal level. |
15 | W/R# | This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU signal. The signals on the data bus are latched at the rising edge of the signal. |
16 | A0 | This is the Data/Command control pad that determines whether the data bits are data or a command. A0="H": the inputs at D0 to D7 are treated as display data. A0="L": the inputs at D0 to D7 are transferred to the command registers. |
17 | R/D# | This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the signal of the 8080 series MPU, and the data bus is in an output status when this signal is "L". |
18 | NC | No Connection |
19 | DISP | Display off when it's pulled low; Display on when it's pulled high. |
20 | NC | No connection |
"모든 쿠키 허용"을 클릭하면 사이트 탐색을 개선하고, 사이트 사용을 분석하며, 마케팅 및 성능 노력에 도움을 주기 위해 쿠키를 귀하의 장치에 저장하는 데 동의한 것으로 간주됩니다. 이 주제에 대한 추가 정보는 당사의 정책에서 확인할 수 있습니다. 개인정보 보호정책