제품 COG LCD WO24064D

SPI / 6800 / 8080 인터페이스 LCD 240x64

모델 번호 WO24064D

►COG LCD
►그래픽 LCD
►240 x 64 점 커서를 포함
►IC: ST7586S
►3.3V 전원
►1/64 듀티 사이클
►인터페이스 : 6800/8080/SPI

설명

WO24064D는 240x64 도트 매트릭스 형식의 단색 COG 그래픽 LCD 모듈입니다. Winstar 표준 COG 240 x 64 그래픽 LCD 디스플레이 WO24064D에는 SPI / 6800 / 8080 인터페이스를 지원하는 ST7586S IC가 하나 내장되어 있으며, 4선 SPI 또는 3선 SPI (선택 사항) 인터페이스를 선택할 수 있습니다. 모듈의 크기는 86.2 x 39.3mm이며 유효 영역 크기는 76.78 x 20.46mm입니다. 이 LCD 모듈은 -20℃에서 +70℃의 온도에서 작동할 수 있습니다. 논리 공급 전압은 3.0V에서 3.4V까지이며, 전형적인 값은 3.3V, 1/64 드라이브 동작입니다. 이 COG LCD 디스플레이는 의료 장비, 테스트 기기, 홈 보안 시스템, 산업 제어 장비 등에 매우 적합합니다.

도면

240x64 COG LCD Display SPI / 6800 / 8080 Interface
Data source ref:WO24064D-TFH#

사양

인터페이스 핀 기능

Pin No. 기호 Level 설명
1 VG P VG is the power of SEG-drivers.
2 XV0 P Negative operating voltage of COM-drivers.
3 V0 P Positive operating voltage of COM-drivers.
V0O is the output of the positive Vop generator.
V0I is the positive Vop supply of LCD drivers.
V0S is the sensor of the positive Vop generator.
V0O, V0I & V0S should be separated on ITO and be connected together by FPC.
4 VM P VM is the non-select voltage level of COM-drivers.
5 VDDA P Analog power for internal booster.  
6 VSS P Ground
7 VD1 P VD1I is the power source of digital circuits.
8 VDDI P Power of interface I/O circuit.
9 CSB Input Chip select input pin.
CSB=“L”: This chip is selected and the MPU interface is active.
CSB=“H”: This chip is not selected and the MPU interface is disabled (D[7:0] are high impedance).
10 IF3 Input These pins select interface operation mode.
IF3 IF2 IF1 MPU interface type
H H L 80 series 8-bit parallel
H L L 68 series 8-bit parallel
L H H 8-bit serial (4-Line)
L H L 9-bit serial (3-Line)
Note: Refer to “Interface Selection” for detailed information.
11 IF2
12 IF1
13 RSTB Input Reset input pin. When RSTB is “L”, internal initialization procedure is executed.
14 /RD(E) Input Read / Write execution control pin. (This pin is only used in parallel interface)
15 D7 I/O The bi-directional data bus of the MPU interface. When CSB is “H”, they are high impedance.
If using serial interface:
D0 is the SDA signal in 4-Line & 3-Line interface.
D1 is the A0 signal in 4-Line interface
16 D6
17 D5
18 D4
19 D3
20 D2
21 D1
22 D0
23 NC   No connection
24 /WR(R/W) Input Read / Write execution control pin. (This pin is only used in parallel interface)
25 A0(SCL) Input The function of this pin is different in parallel and serial interface.
In parallel interface: A0 is register selection input.
A0 = "H": inputs on data bus are display data;
A0 = "L": inputs on data bus are command.
_ In serial interface: this pad will be used as SCL (serial-clock) input
26 VSS P Ground

기계적 데이터

항목 치수 단위
점의 수 240 x 64
모듈 치수 86.2 x 39.3 x 5.1 mm
보기 영역 80.8 x 24.8 mm
활성 영역 76.78 x 20.46 mm
도트 크기 0.30 x 0.30 mm
도트 피치 0.32 x 0.32 mm
듀티 1/64
역광 타입 LED
IC ST7586S
인터페이스 6800/8080/3-Line/4-Line

절대 최대 정격값

항목 기호 최소값 대표값 최대값 단위
작동 온도 TOP -20 +70
보관 온도 TST -30 +80
Digital Power Supply Voltage VDDI -0.3 3.6 V
Analog Power supply voltage VDDA -0.3 3.6 V
LCD Power supply voltage V0-XV0 -0.3 19 V
LCD Power supply voltage VG -0.3 5.5 V

전기적 특성

항목 기호 조건 최소값 대표값 최대값 단위
Supply Voltage For Logic VDD-VSS 3.0 3.3 3.4 V
Supply Voltage For LCM XV0-V0 Ta=-20℃
Ta=25℃
Ta=70℃

9.8

10.0

10.2
V
V
V
Input High Volt. VIH 0.7 VDD VDD V
Input Low Volt. VIL VSS 0.3VDD V
Output High Volt. VOH 0.8VDD VDD V
Output Low Volt. VOL VSS 0.2VDD V
Supply Current(No include LED Backlight) IDD VDD=3.3V 1.5 mA

Search Keyword: lcd 240x64, lcd 240 x 64, 240x64 lcd, 240 x 64 lcd
go top
close