Modello numero WF101JTYAHMNB0
►Risoluzione : 1024×600 punti
►Dimensione : 10.1 pollici
►Direzione di visione : IPS
►Interfaccia : MIPI DSI
►Driver IC : EK79007AD3+EK73217BCGA
►Scheda di controllo : No
►Luminosità (cd/m2) : 400
►Cornice di fissaggio : No
►Touch Screen : con pannello touch capacitivo (PCAP)
►Detect Point : 5 Fingers
►PCAP Interfaccia : USB (I2C available)
DISEGNO
SPECIFICHE TECNICHE
Funzione dei Pin di Interfaccia
TFT LCD Module
Pin No. | Simbolo | Funzione |
---|---|---|
1 | VLED+ | LED Anode |
2 | VLED+ | LED Anode |
3 | VGH | Positive power for TFT |
4 | VGL | Negative power for TFT |
5 | UPDN | Gate up or down scan control. UPDN = ”L”, STV2 output vertical start pulse and UD pin output logical “L” to Gate driver. (default) UPDN = ”H”, STV1 output vertical start pulse and UD pin output logical “H” to Gate driver |
6 | SHLR | Source right or left sequence control. SHLR = ”L“, shift left: last data = S1←S2←S3….......←S1536 = first data. SHLR = ”H“, shift right: first data = S1→S2→S3….....→S1536 = last data.(default) |
7 | VLED- | LED Cathode |
8 | VLED- | LED Cathode |
9 | AVDD | Analog power |
10 | GND | Digital ground |
11 | D3P | MIPI data input. |
12 | D3N | MIPI data input. |
13 | GND | Digital ground |
14 | D2P | MIPI data input. |
15 | D2N | MIPI data input. |
16 | GND | Digital ground |
17 | CLKP | MIPI clock input |
18 | CLKN | MIPI clock input |
19 | GND | Digital ground |
20 | D1P | MIPI data input. |
21 | D1N | MIPI data input. |
22 | GND | Digital ground |
23 | D0P | MIPI data input. |
24 | D0N | MIPI data input. |
25 | GND | Digital ground |
26 | STBYB | Standby mode. STBYB = ”H“,normal operation(default) STBYB = ”L”, timing controller, source driver will turn off, all output are GND. |
27 | RESET | Global reset pin. Active Low to enter Reset State. Normally pull high. Connecting with an RC reset circuit for stability. |
28 | VDD (1.8V) | Digital power |
29 | VDD (1.8V) | Digital power |
30 | VCOMI | Common voltage |
PCAP PIN Definition
Pin | Simbolo | Funzione |
---|---|---|
1 | USB_VSS | System ground |
2 | USB_VDD 5V | Power supply |
3 | USB_D+ | Data + |
4 | USB_D- | Data - |
5 | VSS | System ground |
6 | SDA | I2C data input and output |
7 | SCL | I2C clock input |
8 | RST | External Reset, Low is active |
9 | INT | External interrupt to the host |
10 | VDDT 3.3 | Power supply |
Specifiche generali
Articolo | Dimensioni | Unità |
---|---|---|
Dimensione | 10.1 | pollici |
A matrice di punti | 1024 RGB x 600 | dots |
Dimensione del modulo | 235(W) x 143(H) x 8.78(D) | mm |
Area attiva | 222.72 (H) x 125.28(V) | mm |
Passo del Dot | 0.2175(W) x 0.2088(H) | mm |
Tipo LCD | TFT, Nero, Trasmissivo | |
Interfaccia | 4-Lanes MIPI | |
Driver IC | EK79007AD3 + EK73217BCGA o equivalente | |
Direzione di visione | 85/85/85/85 | |
Proporzioni dell’area visiva (ratio) | 16:9 | |
Tipo di backlight | LED, Bianco | |
PCAP IC | ILI2511 o equivalente | |
PCAP Interfaccia | USB (I2C available) | |
PCAP FW versione | V6.0.0.0.62.90.1.2 | |
Con / senza Touch Panel | con pannello touch capacitivo (PCAP) | |
Superficie | Bagliore (Glare) |
Valori massimi assoluti
Articolo | Simbolo | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|
Temperatura di lavoro | TOP | -20 | - | +70 | ℃ |
Temperatura di stock | TST | -30 | - | +80 | ℃ |
Caratteristiche elettriche
Typical Operation Conditions (At Ta = 25 °C,)
Articolo | Simbolo | Valore Min | Valore tipico | Valore massimo | Unità |
---|---|---|---|---|---|
Digital Power Supply Voltage For LCD | VDD | 1.71 | 1.8 | 1.89 | V |
Analog Power Supply Voltage | AVDD | 9.89 | 10.2 | 10.5 | V |
Gate On Power Supply Voltage | VGH | 19.4 | 20.0 | 20.6 | V |
Gate Off Power Supply Voltage | VGL | -10.3 | -10.0 | -9.7 | V |
Common Power Supply Voltage | VCOMI | 4.0 | 4.3 | 4.6 | V |
Supply PCAP | VDDT | 3.0 | 3.3 | 3.6 | V |
IVDDT | 90.5 | 115 | mA | ||
USB_VDD 5V | 4.4 | 5.0 | 5.5 | V | |
I VDD 5V | — | 97.8 | 120 | mA |