Home Prodotti Display OLED Display OLED Grafici WEO006432A

Display OLED Grafici 64x32, 0.49"

Modello numero WEO006432A

►Tipo: grafico
►Struttura: COG
►Dimensione: 0.49 pollici
►64x32 a matrice di punti
►A bordo Controllore SSD1306BZ
►Alimentatore 3V
►1/32 duty
►Interfaccia: I2C

DESCRIZIONE

  • WEO006432AW : Bianco
  • WEO006432AL : Giallo
  • WEO006432AS : Cielo blu (might have MOQ)

DISEGNO

Micro OLED Display, 0.49 OELD, 64x32 OLED Micro Display, Micro OLED Screen - WEO006432A

SPECIFICHE TECNICHE

Funzione dei Pin di Interfaccia

No. Simbolo Funzione
1 C2N Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2P
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL Host Data Input/Output Bus
11 SDA When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Dati meccanici

Articolo Dimensioni Unità
A matrice di punti 64 x 32 Dots
Dimensione del modulo 14.5 × 11.6 × 1.26 mm
Area attiva 11.18 × 5.58 mm
Dimensioni del Dot 0.153 × 0.153 mm
Passo del Dot 0.175 × 0.175 mm
Modalità display Matrice passiva
Colore display monocromatici
Drive Duty 1/32Duty
IC SSD1306BZ

Caratteristiche elettriche

Articolo Simbolo Condizione Valore Min Valore tipico Valore massimo Unità
Supply Voltage for Logic  VDD 2.8 3 3.3 V
Supply Voltage for Display  VCC 7 7.5 7.8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
50% Check Board operating Current ICC VCC=7.5V 5 20 mA
 

Search keyword: 64x32 oled, oled 64x32,0.49 oled, 0.49" oled, 0.49 inch oled, oled 0.49, oled 0.49"

go top
close